Search Results
Post Author Forum Replies Views Posted [asc]
  0 Thread: Gluing onto Polyurethane Finished Wood?
Post: RE: Gluing onto Polyurethane Finished Wood?

fredhargis Wrote: (06-09-2021, 02:39 PM) -- Maybe clear some of the varnish off where the letters go and use PVA to glue the letters to the wood itself? Removing the finish under the letters may b...
tbr Woodworking 12 2,098 06-09-2021, 03:02 PM
  0 Thread: Gluing onto Polyurethane Finished Wood?
Post: RE: Gluing onto Polyurethane Finished Wood?

MT WoodworkerInstead of glue, possibly just use a pin nailer? The letters are very small so a pin nail would be too large. But thanks for the suggestion.
tbr Woodworking 12 2,098 06-09-2021, 02:58 PM
  0 Thread: Gluing onto Polyurethane Finished Wood?
Post: Gluing onto Polyurethane Finished Wood?

I would like to glue small wooden letters to wood that has a polyurethane finish. What would be the best glue for this?  Would Titebond work or is there something that will hold better?
tbr Woodworking 12 2,098 06-09-2021, 02:27 PM
  0 Thread: Plunge Router with Good Depth Control
Post: Plunge Router with Good Depth Control

I currently have a Porter Cable router with a plunge base. Over the years of use, the locking screw that holds the sliding depth rod no longer securely locks the rod place. I have replaced the locking...
tbr Woodworking Power Tools 2 870 10-22-2020, 06:54 PM
  0 Thread: Calibrating Miter Gauge Woes?
Post: RE: Calibrating Miter Gauge Woes?

You should check to make sure your blade is parallel to the miter slot using a dial indicator (I use an A-Line-It made by Incra). You then can build a sled with a fixed 45 degree fence using a draftin...
tbr Woodworking Power Tools 35 18,464 11-10-2017, 07:21 PM
  0 Thread: Looking for bandsaw resawing blade suggestions
Post: RE: Looking for bandsaw resawing blade suggestions

Thank you everyone for your suggestions and advice. I would like to get a carbide tipped blade but current budget considerations have place the them out of reach for the moment. As such, I purchased a...
tbr Woodworking Power Tools 26 22,424 10-27-2017, 07:12 PM
  0 Thread: Looking for bandsaw resawing blade suggestions
Post: RE: Looking for bandsaw resawing blade suggestions

Jason, Thanks for the detailed reply. Although I originally mentioned that I was looking for a 3/4” blade, if that is not necessarily suitable for the 325, would a 1/2” blade handle the type of res...
tbr Woodworking Power Tools 26 22,424 10-21-2017, 09:21 PM
  0 Thread: Looking for bandsaw resawing blade suggestions
Post: Looking for bandsaw resawing blade suggestions

I have a Rikon 10-325 bandsaw (111” blades) and am planning to buy a 3/4” blade for resawing hardwood up to 4” thick to make 1/8” thick pieces for inlay. I am looking for suggestions for a good qualit...
tbr Woodworking Power Tools 26 22,424 10-21-2017, 07:39 PM
  0 Thread: Miter Saws ideas
Post: RE: Miter Saws ideas

Yes I am talking about the zero clearance fence.  I used a piece of MDF and screwed into a extra table saw insert. As for the stop, it works well and I have used for table saw cuts other than segments...
tbr Woodturning 9 4,712 08-09-2017, 11:00 AM
  0 Thread: Miter Saws ideas
Post: RE: Miter Saws ideas

I started out making segments using a miter saw, but quickly found my table saw to be much more accurate and reproducible. I built a Wedgie Sled as described on  this web site as well as  You Tube vid...
tbr Woodturning 9 4,712 08-08-2017, 07:41 PM

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.