Search Results
Post Author Forum Replies Views Posted [asc]
  0 Thread: Dewalt Planer
Post: RE: Dewalt Planer

AHill Wrote: (05-19-2022, 06:16 AM) -- Not so sure about that, since the strain of one small cutter on a helical cutter is far less than the strain of a full length blade.  I don't notice the differe...
jeffss Woodworking Power Tools 9 884 05-19-2022, 08:36 AM
  0 Thread: Dewalt Planer
Post: RE: Dewalt Planer

Yes, since there is always a cutter on the wood it's going to strain more than the three straight blades. I just don't get greedy and take the extra pass.
jeffss Woodworking Power Tools 9 884 05-18-2022, 10:52 AM
  0 Thread: Wrong size jointer knives
Post: RE: Wrong size jointer knives

Yes on the jack screws. I guess my concern was raising them to the point of not getting a good grip. Raised them and it looks good. thanks.
jeffss Woodworking Power Tools 9 756 04-06-2022, 08:41 AM
  0 Thread: Wrong size jointer knives
Post: RE: Wrong size jointer knives

Should have been more clear. Old blade is 8"x7/8"x1/8". New blade is 8"x3/4"x1/8".
jeffss Woodworking Power Tools 9 756 04-05-2022, 09:02 PM
  0 Thread: Wrong size jointer knives
Post: Wrong size jointer knives

I'm replacing knives on a older Powermatic model 60. The new blades are 1/8" shorter. They fit in the head ok but I will have to lower the outfeed side. Lowering it will also move it slightly away fro...
jeffss Woodworking Power Tools 9 756 04-05-2022, 11:57 AM
  0 Thread: My CNC Arrived
Post: RE: My CNC Arrived

Nothing fancy on the wires. The 2 Y go through the table. The router power goes up the dust collection. X and Z are in a loop on the side of the table. Everything pinned down and secure.
jeffss Woodworking Power Tools 44 3,544 03-19-2022, 09:02 AM
  0 Thread: dust collection
Post: dust collection

[delete] thanks anyway
jeffss Woodworking Power Tools 0 315 03-16-2022, 09:50 AM
  0 Thread: My CNC Arrived
Post: RE: My CNC Arrived

Moving along here. Flattened spoil board, cut grid. Threw on a couple of drawer fronts.  Since I and working via usb flash drive I added a port to the front of the table. Reaching around was beginni...
jeffss Woodworking Power Tools 44 3,544 03-12-2022, 08:05 PM
  0 Thread: My CNC Arrived
Post: RE: My CNC Arrived

Got mine early. Went with the Woodworker. Only took 4 weeks. Had to clear up space and run some dust collection. Ready to flatten the spoil board and cut a grid and holes. Fingers crossed!
jeffss Woodworking Power Tools 44 3,544 03-06-2022, 07:09 PM
  0 Thread: My CNC Arrived
Post: RE: My CNC Arrived

Looks good.  I am sharing in your fun until mine gets here.  Keep posting the progress!
jeffss Woodworking Power Tools 44 3,544 02-23-2022, 10:45 PM
  0 Thread: My CNC Arrived
Post: RE: My CNC Arrived

Looks great! Waiting on mine. If I can ask, what is your top size and where do you plan on mounting the controller?
jeffss Woodworking Power Tools 44 3,544 02-23-2022, 09:17 AM
  0 Thread: Onefinity CNC
Post: RE: Onefinity CNC

Mine is ordered. Lots of time to set up shop. I thought I had a big shop, but trying to figure out where to drop the this beast is driving me nuts. Looks like the down draft table is coming down. Wen...
jeffss Woodworking Power Tools 16 6,795 02-18-2022, 09:10 PM
  0 Thread: Sawstop and molding head.
Post: RE: Sawstop and molding head.

John Mihich Wrote: (02-13-2022, 08:53 PM) -- I have a SS cabinet saw and would like to use my craftsman molding head.  I do have the dado module but the molding head is smaller.  I have not tried usi...
jeffss Woodworking Power Tools 4 606 02-14-2022, 12:09 AM
  0 Thread: jessem router lift parts
Post: RE: jessem router lift parts

rwe2156 Wrote: (01-17-2022, 12:36 PM) -- I have noticed this on mine (MastRLift II). I'm not sure what it means, guess I should call Jessem. -- So I did an inspection on the under side and found...
jeffss Woodworking Power Tools 7 833 01-19-2022, 02:38 PM
  0 Thread: Saw Stop bypass
Post: Saw Stop bypass

Question. How often do you run your Saw Stop in bypass mode.  Or, when would you run in bypass. Seems any glue ups or staining makes me want to run in bypass.
jeffss Woodworking Power Tools 7 707 01-16-2022, 10:48 PM
  0 Thread: jessem router lift parts
Post: RE: jessem router lift parts

Question. Did you notice the lift screw getting "tight" as you raised to change a bit? Mine is not as smooth as before. Just wondering.
jeffss Woodworking Power Tools 7 833 01-14-2022, 09:52 AM
  0 Thread: Router table upgrade ideas
Post: RE: Router table upgrade ideas

Skiathos Wrote: (12-06-2021, 09:53 PM) -- I'm starting from scratch. Which router are you going to end up using in your table ? -- Going to start with the dewalt 618 . I like the one wrench bit cha...
jeffss Woodworking Power Tools 26 3,679 12-07-2021, 09:57 AM
  0 Thread: Router table upgrade ideas
Post: RE: Router table upgrade ideas

Ended up with a JessEm lift, Woodpecker fence, home made top, and treated myself to a sled.  Base build coming next.  thanks all
jeffss Woodworking Power Tools 26 3,679 12-04-2021, 09:42 PM
  0 Thread: Router table upgrade ideas
Post: RE: Router table upgrade ideas

Tapper Wrote: (11-22-2021, 10:08 PM) -- I have two router tables (don't ask me how this happened!); one has a Woodpecker PRL (original model) and the other with an Incra Mast-R-Lift II with one of In...
jeffss Woodworking Power Tools 26 3,679 11-23-2021, 10:14 AM
  0 Thread: Router table upgrade ideas
Post: RE: Router table upgrade ideas

This is my current setup since I got rid of my router table. I will replace the top because it's sagging and rotate the plate 90 degrees. No router lift at this time and my fence is just a piece of st...
jeffss Woodworking Power Tools 26 3,679 11-18-2021, 12:24 PM

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.