Woodnet Forums › › Active › Woodworking Power Tools v
Aluminum router plate
Thread Modes
Aluminum router plate
doobes Offline
Member
Posts: 6,334
Threads: 4
Joined: Mar 2008
Location: Williamsburg, VA
#10
10-30-2015, 09:01 PM
All,

I'm looking for a good quality aluminum router plate to mount my Bosch 1617 router to.

Can you recommend one?

Thanks
chris
Website Find
Reply
Routerman Offline
Member
Posts: 3,268
Threads: 0
Joined: Oct 1999
#11
10-30-2015, 09:11 PM
Into your table or for hand use?
Cutter hole diameter?
Pat Warner
Website Find
Reply
blackhat Offline
Member
Posts: 22,714
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
#12
10-30-2015, 09:19 PM
. I hadn't finished reading his question and my proposed answer was get ahold of Pat the Routerman.
Blackhat

Bad experiences come from poor decisions. So do good stories. 


Find
Reply
Big Dave Offline
Honored Veteran
Posts: 6,755
Threads: 0
Joined: Aug 2001
Location: Post Falls, ID
#13
10-30-2015, 10:18 PM
If it's for table use, I've been using a couple from Rockler for a PC 7518 and 690 for almost 20 years with no problems...

Dave
"One should respect public opinion insofar as is necessary to avoid starvation and keep out of prison, but anything that goes beyond this is voluntary submission to an unnecessary tyrany, and is likely to interfere with happiness in all kinds of ways."
Website Find
Reply
Aram Offline
Member
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
#14
10-30-2015, 10:22 PM
For a table, love my Woodpecker's.
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery

Web: My woodworking photo site
Find
Reply
doobes Offline
Member
Posts: 6,334
Threads: 4
Joined: Mar 2008
Location: Williamsburg, VA
#15
10-31-2015, 06:39 AM
Routerman said:


Into your table or for hand use?
Cutter hole diameter?



Sorry, table use. Ideally I'd like to have inserts for different diameter cutters, but honestly, I never used anything but the smallest one on my previous plate. I just checked and that hole is 1 1/4".

At this point I'm vacillating between the Pro-Plate (Bench Dog, Rockler, et al) and the Woodpecker.

Is the extra thickness of the Woodpecker a benefit? It's 3/8" thick vs 1/4" for the Pro Plate.
chris
Website Find
Reply
Routerman Offline
Member
Posts: 3,268
Threads: 0
Joined: Oct 1999
#16
10-31-2015, 08:37 AM
If it's flat, use 3/8". Very little depth penalty.
Moreover, the 7518 has more up/down motor travel than any router.
Pat Warner
Website Find
Reply
doobes Offline
Member
Posts: 6,334
Threads: 4
Joined: Mar 2008
Location: Williamsburg, VA
#17
11-01-2015, 07:57 AM
Routerman said:


If it's flat, use 3/8". Very little depth penalty.
Moreover, the 7518 has more up/down motor travel than any router.



Thanks Pat.

I think I will bite the bullet and go for the Woodpeckers



cheers,
chris
Website Find
Reply
doobes Offline
Member
Posts: 6,334
Threads: 4
Joined: Mar 2008
Location: Williamsburg, VA
#18
11-07-2015, 03:16 PM
I got the plate on Wednesday. All I can say is wow!

I'm a cheap a$$ bastage and this was well worth the asking price.
chris
Website Find
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.