Posts: 851
Threads: 0
Joined: Apr 2006
Location: Central MA
11-28-2018, 01:21 PM
(This post was last modified: 11-28-2018, 01:22 PM by jlanciani.)
Just for the record, you can get clear PVC primer. The purple just makes it easier for the plumbing inspectors...
Posts: 5,661
Threads: 1
Joined: Mar 2008
Location: Flemington, New Jersey
11-28-2018, 01:35 PM
(This post was last modified: 11-28-2018, 06:18 PM by AgGEM.)
(11-28-2018, 01:21 PM)jlanciani Wrote: Just for the record, you can get clear PVC primer. The purple just makes it easier for the plumbing inspectors...
I know....I am the Charlie Brown pen / pencil pal of purple plastic plumbing primer.....phooey...
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
So your factory 4" dc outlet doesn't work well??
I have a MM16, almost identical saw. I use the factory port with no problems.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 5,661
Threads: 1
Joined: Mar 2008
Location: Flemington, New Jersey
(11-28-2018, 11:55 PM)Stwood_ Wrote: So your factory 4" dc outlet doesn't work well??
I have a MM16, almost identical saw. I use the factory port with no problems.
I use a shop vac pulling though a Dust Deputy.
I do notice an improvement with the Cosman approach. By how much would be guess work.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Ok. Have you had a dust collector hooked to it before?
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 5,661
Threads: 1
Joined: Mar 2008
Location: Flemington, New Jersey
(11-29-2018, 10:00 AM)Stwood_ Wrote: Ok. Have you had a dust collector hooked to it before?
No on a dust collector / 4" plumbing.
Yes, Shop vac through the OEM 4" port. Only the top port.
Posts: 3,545
Threads: 1
Joined: May 2004
Location: Wisconsin
11-30-2018, 12:04 PM
(This post was last modified: 11-30-2018, 12:07 PM by Alan S.)
One option is to use a soda bottle as the end of the duct under the table. It can deform or even get cut when you tilt the table without a real problem, though it does sound horrendous as the blade cuts it.
To make tilting the blade quick and accurate, your saw may have the bolt used as a stop under the table. With the Delta style, you can make a series of bolts to swap out; when you adjust the tilt you simply loosen trunnions, put in the stop for the angle you want, push the table down to the stop and tighten the trunnions. I think this approach was described in John White's "Care and repair of shop machines".
Posts: 5,661
Threads: 1
Joined: Mar 2008
Location: Flemington, New Jersey
(11-29-2018, 02:59 AM)AgGEM Wrote: I use a shop vac pulling though a Dust Deputy.
I do notice an improvement with the Cosman approach. By how much would be guess work.
Update: Bevel fence jig is almost finished, first test cut looks promising. Will post photos when the jig is more functional.
I had my first look inside the lower housing, after a month with the new Cosman DC setup. I can report significant improvement in dust collection with his plumbing method. There was very little dust to be found.
