Posts: 30
Threads: 0
Joined: Jan 2019
Hi All,
I have a cabinet saw and a 650CFM dust collector. There has always been some amount of saw dust that came out of the spaces between the table top and the cabinet. However, since I added a Thien Baffle to the system, I'm getting a lot of saw dust coming out of those spaces.
Is this normal? Is there something I can do to stop it?
Thx, Jeff
Jeff in Los Angeles
Posts: 12,606
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
I'll take a stab. You have a minimal (I think) DC and adding the separator reduced the flow further. Separators are always a good thing, but they do introduce some drag on the overall system...that is the nature of the beast. The best way to reduce the amount of dust escaping the cabinet would be to get a larger collector (if my assumption on the size of yours is correct).
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
I stuffed pink fiberglass wall insulation into the holes under my saw. Works quite well.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 30
Threads: 0
Joined: Jan 2019
(10-29-2019, 02:36 PM)fredhargis Wrote: I'll take a stab. You have a minimal (I think) DC and adding the separator reduced the flow further. Separators are always a good thing, but they do introduce some drag on the overall system...that is the nature of the beast. The best way to reduce the amount of dust escaping the cabinet would be to get a larger collector (if my assumption on the size of yours is correct)
Thanks for the feedback. I've always had a separator, just upgraded to the Thein design. Also converted from ribbed hose to smooth-inside hose.
Jeff in Los Angeles
Posts: 30
Threads: 0
Joined: Jan 2019
(10-29-2019, 02:39 PM)Stwood_ Wrote: I stuffed pink fiberglass wall insulation into the holes under my saw. Works quite well.
Interesting. I thought the holes were necessary for air to flow through the cabinet?
Jeff in Los Angeles
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Not my 1022 Griz. There's enough holes by the blade insert, the tilt knob, the height knob......
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 2,721
Threads: 0
Joined: Feb 2002
Quote:I stuffed pink fiberglass wall insulation into the holes under my saw. Works quite well.
Yup, I used left over Kaizen Foam on my Jet Contractors saw ... also filled the hole at the front where the height adjustment wheel rotates during angled cuts.
There's enough "leakage" elsewhere to allow proper draw.
~Dan.
Posts: 16,604
Threads: 0
Joined: Oct 2002
Location: Ra-cha-cha, NY
10-30-2019, 02:22 PM
(This post was last modified: 10-30-2019, 02:23 PM by TDKPE.)
(10-29-2019, 05:57 PM)MVWoodworks Wrote: Interesting. I thought the holes were necessary for air to flow through the cabinet?
They are, but if dust is coming out of a hole, there isn't enough air flowing into that hole, so plug or guard it.
But it sounds like you really need a larger DC system, I'm sorry to say. It takes a LOT of air movement to capture dust in a TS without some escaping, and that doesn't even include a blade guard with DC port.
Edit: Oh, and that 650 cfm is probably moving around 300 cfm with bags and hose and machine port attached.
Tom
“This place smells like that odd combination of flop sweat, hopelessness, aaaand feet"
