Posts: 10,731
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
I have a friend who inherited a vintage oak steering wheel. He wants to refinish the wheel by sanding off the old finish, but he noticed a brass ring around the hub. He wants to know how he can prevent brass particles from contaminating the wood. Is this something he should worry about? Is there some way to protect the wood from brass particles before or during sanding? I'm thinking either use a chemical stripping compound vs. sanding, or just go ahead and sand but use compressed air frequently to blow the dust off. Any other suggestions? The brass parts are not removable without damaging the wood, so taking it apart is not an option.
Still Learning,
Allan Hill
Posts: 4,447
Threads: 0
Joined: Jan 2005
The stripper may damage the brass.Possibly a card scraper and then Scotch Brite pads to remove the stripper. I know that ferros stock will stain oak,not sure about brass.Can the brass be masked with tape ?
mike
Posts: 3,268
Threads: 0
Joined: Oct 1999
Test on scrap.
Pat Warner
Posts: 31,166
Threads: 2
Joined: Mar 2003
Location: Athens, TN
Probably a dense wood without pores. I doubt the brass filings would make a difference to the wood. I'd just sand and refinish and not really question it.
Rocket Science is more fun when you actually have rockets.
"The Constitution is not an instrument for the government to restrain the people, it is an instrument for the people to restrain the government." -- Patrick Henry
Posts: 5,657
Threads: 0
Joined: May 2005
Location: Centre County Pennsylvania
I would test to see if it's shellac. If so, I probably would French polish the existing finish
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
When I have use brass or other metal inlay I soak it with Shellac and then nothing goes into the wood after that.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 8,963
Threads: 0
Joined: Sep 2010
He will be better off stripping the wheel. He can try soy stripper but will most likely need to use the more toxic methylene chloride paint stripper. Sanding a curved surface to remove all finish is problematic particularly with the brass.
Klean-Strip SR-72 Premium Paint Stripper Spray would likely do the job. I think that HD carries it.
homo homini lupus
"The best lack all conviction, while the worst are full of passionate intensity." Yeats
Si vis pacem, para bellum
Quodcumque potest manus tua facere instaner opere Ecclesiastes
Posts: 375
Threads: 0
Joined: Jun 2006
Location: Hi "Mojave" Desert
Hey Allen,
I have a Black Powder rifle kit that has brass inlayed parts. I have had a minor issue when using fine sandpaper with the pores of the walnut stock, but a wipe down with MS seems to get rid of the fine brass powder. I have been finishing the stock by sanding in shellac and so far it is coming along OK. I’m not sure how the shellac will work out in the long term for a rifle stock.
When you don’t get what you want, you get experience!
Posts: 2,392
Threads: 0
Joined: Jan 2008
Location: Irving, Tx
FWIW....Just a guess, I suspect when the thing was originally made, the brass and wood were assembled then sanded smooth. Like someone else suggested, sand and follow with compressed air.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Posts: 10,731
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
Thanks for all the replies so far. My friend really appreciates the input.
I should mention that he also said the wheel was cracked and splintered, so the restoration requires sanding, followed by some minor filling in of cracks. He's relatively adept at woodworking, but not with this particular task.
Still Learning,
Allan Hill
