Posts: 1,030
Threads: 3
Joined: Jun 2011
Location: N. Cincy inside the loop
Every so often this forum has a scary story about tablesaw kickback. I want to add my recent experience with a table router. Normally everything is set up properly and I feed the wood in the correct direction. In a moment of mental lapse, I set the fence back and fed a 24" piece of 1x3 from RIGHT to LEFT BETWEEN the bit and the fence - therefore, WITH the rotation, not against it. Halfway through, the rotation of the bit launched the board with such speed and force that the board imbedded itself in the drywall more than five feet away. Thank God no one was standing in the way or they would have been impaled.
When you read about not making a climb cut, you don't realize the force it can produce.
As much as I thought I knew what I was doing, I made a mental mistake that could have been catastrophic. It's time to go back and take a refresher course for me. Don't make my mistake - review your manual and its precautions. It may save your life.
Posts: 22,328
Threads: 0
Joined: Dec 2005
Location: Oakdale, MN
Good thing it wasn't a short piece and your hands went with the board into the bit.
Once Favre hangs it up though, it years of cellar dwelling for the Pack. (Geoff 12-18-07)
Posts: 4,004
Threads: 0
Joined: Apr 2002
Posts: 22,328
Threads: 0
Joined: Dec 2005
Location: Oakdale, MN
One other method I use when dealing with routers, small parts I bring to the router, and large parts I bring the router to the part.
Not knowing exactly what you were doing, a 24" long board, I would have likely brought the router to the board, and built a jig or straightedge setup.
Once Favre hangs it up though, it years of cellar dwelling for the Pack. (Geoff 12-18-07)
Posts: 12,911
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
Thanks for posting that. I'll bet we all make mental mistakes more often than we like to admit. Fortunately, they rarely result in more than a ruined piece of wood and a wake up call to think more about every operation, every time.
John
Posts: 3,859
Threads: 0
Joined: Nov 2000
A good post, a worthwhile warning. Another thing to bear in mind is having a routine place to stand, a routine disposition of one's hands and fingers.
Safety training, for me, included an understanding of acceptable and unacceptable places to stand. If the unwanted accident should occur, a person who isn't standing in the wrong place is in a much better situation. This isn't to say that accidents are desirable, but simply that IF they occur, there is desirable and undesirable real estate.
Posts: 1,030
Threads: 3
Joined: Jun 2011
Location: N. Cincy inside the loop
packerguy® said:
Good thing it wasn't a short piece and your hands went with the board into the bit.
That thought sends chills up my spine - it was a 1/2" diameter bull nosed bit that was still in the router from a job I had just finished. I was using the straight portion of the bit to dress the edge of the 1x3 (why change the bit if I didn't have to - and maybe that was another mistake). One massive chunk of steel whirling around. Ugh!!!
Posts: 901
Threads: 0
Joined: Jul 2006
Location: Fripp Island, SC
Good post has lead to a good thread.
Posts: 1,030
Threads: 3
Joined: Jun 2011
Location: N. Cincy inside the loop
jteneyck said:
Thanks for posting that. I'll bet we all make mental mistakes more often than we like to admit. Fortunately, they rarely result in more than a ruined piece of wood and a wake up call to think more about every operation, every time.
John
John, I've caught edges before or had the router jump, but this was the scariest thing I've experienced. Totally frightening when that board launched and then I heard it hit and saw it sticking out of the wall. I stood there for a good five minutes just thinking about what happened.
Posts: 2,230
Threads: 0
Joined: Sep 2007
Router tables still scare me a bit. I still flinch when I turn it on. Especially on larger bits like panel routers.
