Woodnet Forums › › Active › Woodworking Hand Tools v
Rehabilitating a 200-year-old Jaeger Rifle
Thread Modes
Rehabilitating a 200-year-old Jaeger Rifle
Window Guy Offline
Honored Veteran
Posts: 13,842
Threads: 0
Joined: Jun 2001
#21
09-24-2013, 09:00 AM
Ditto on the Welcome back Bob, and I also enjoyed this write up. My Father collected and restored old guns including a few muzzle loaders. I as a Kid enjoyed watching him work on his Guns.

Thanks for sharing !

Steve
Find
Reply
Timberwolf Offline
Honored Veteran
Posts: 116,242
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
#22
09-24-2013, 09:21 AM
Good job as usual, Bob...We've missed you and hope you continue to join us again here in the hand tool section..
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Find
Reply
CLETUS Offline
Rufus
Posts: 29,870
Threads: 0
Joined: Jan 2008
Location: Mid-MI
#23
09-24-2013, 09:32 AM
Wow.

I've read your stuff on other sites and have seen you mentioned here.

Glad to see you're back.
Mark

I'm no expert, unlike everybody else here - Busdrver


Nah...I like you, young feller...You remind me of my son... Timberwolf 03/27/12

Here's a fact: Benghazi is a Pub Legend... CharlieD 04/19/15

Find
Reply
Big Dave Offline
Honored Veteran
Posts: 6,755
Threads: 0
Joined: Aug 2001
Location: Post Falls, ID
#24
09-24-2013, 04:13 PM
You are, truly, a man of many talents, Bob...


Love the post. Love the rifle. And love the lesson...


Thanks!

And welcome back!!

Dave
"One should respect public opinion insofar as is necessary to avoid starvation and keep out of prison, but anything that goes beyond this is voluntary submission to an unnecessary tyrany, and is likely to interfere with happiness in all kinds of ways."
Website Find
Reply
Cian Offline
Maxed out Honored Member
Posts: 30,422
Threads: 1
Joined: Dec 2002
Location: IL or NC <coin toss>
#25
09-24-2013, 09:33 PM


Great to see you on the Forum, Bob!
The Neanderthal Index and The Power Index
Website Find
Reply
Bill_Houghton Offline
Member
Posts: 3,017
Threads: 1
Joined: Aug 2009
#26
09-24-2013, 09:45 PM
What always amazes me about the old rifles and muskets is how little wood there is in the area of the firing mechanism and trigger; and yet, they don't fall apart when fired.
Find
Reply
Bob Smalser Offline
Member
Posts: 390
Threads: 0
Joined: Apr 2007
#27
09-25-2013, 12:12 AM
Bill_Houghton said:


What always amazes me about the old rifles and muskets is how little wood there is in the area of the firing mechanism and trigger; and yet, they don't fall apart when fired.



That's why I stress grain orientation so heavily. If cut from a straight blank and not a tree crotch or by heat-bending, by the hundred year mark the stock will likely either crack at the lock, or the toe.



This also applies to all pieces y'all are making from wood that are thin and stressed.

The modern long rifle builders who don't appreciate this are legion, and many get a lot of money for what is essentially second-rate work.

Here's what a long stock should look like, with the barrel channel lined up with the benchtop strips:

http://www.wkfinetools.com/contrib/bSmalser/bobSmalser-index.asp
Website Find
Reply
MarvW Offline
Member
Posts: 3,776
Threads: 0
Joined: Aug 2007
#28
09-25-2013, 09:54 AM
Outstanding restoration.

It represents a collection of skills acquired over many years. So much more involved than what we see in these pictures.

Great pictorial. It's inspiring.
Catchalater,
Marv


I did then what I knew how to do. Now that I know better, I do better.”
― Maya Angelou

I'm working toward my PHD.  (Projects Half Done)
Find
Reply
jgourlay Offline
Just Promoted to troublemaker
Posts: 11,420
Threads: 0
Joined: Dec 2002
#29
09-25-2013, 01:16 PM
Welcome back!
MAKE: Void your warranty, violate a user agreement, fry a circuit, blow a fuse, poke an eye out...  www.makezine.com

No Good Deed Goes Unpunished

Find
Reply
SlashDev Offline
Member
Posts: 695
Threads: 0
Joined: Dec 2004
#30
09-25-2013, 10:19 PM
Another great set of archive-worthy posts! I'm always impressed by the no-nonsense approach, backed by decades of experience.


If I may humbly offer the next in a series of collectible WoodNet posters:




It's based on an inane Ethan Allen catalogue cover, first discussed here.

Thanks for taking the time to document the process.

Cheers,
/dev
Find
Reply


Forum Jump:


Users browsing this thread: 4 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.