Posts: 794
Threads: 0
Joined: Nov 2006
Location: Halstead, ks
One of our Guild members is giving away some of his tools in preparation for a move. An 8" tablesaw blade was among the items.
It has 8 flat ground teeth with 3/4" deep gullets. It is a Sears product with a catalog # 9-32478 and labeled 8" General Purpose Carbide Tipped
What would this have been used for? It doesn't fit my understanding of a General Purpose blade.
Thanks.
Bill
Posts: 3,268
Threads: 0
Joined: Oct 1999
Probably a slotter, kerf = ?
Pat Warner
Posts: 794
Threads: 0
Joined: Nov 2006
Location: Halstead, ks
Posts: 23,200
Threads: 0
Joined: Jan 2003
That is the full catalog description from 1972.
It is difficult to free fools from the chains they revere. - Voltaire
Know what, Bob? You win. CharlieD, 4/21/2008
I salute you. Hail MGoBlue! Hail MGoBlue! Hail MGoBlue!!!! CRR, 2/19/2008
Posts: 16,604
Threads: 0
Joined: Oct 2002
Location: Ra-cha-cha, NY
My dad had that same blade on his 50's Craftsman TS. It's the only blade that saw has ever had. My 1952 catalog lists it as p/n 9A4943, and touts its safety aspects, and that it can't grab stock and kick it back to the operator. It sold for $12.95, which would be something like $117 in today's dollars.
That was probably the catalog he bought his TS from, by the way.
Tom
“This place smells like that odd combination of flop sweat, hopelessness, aaaand feet"
Posts: 5,733
Threads: 2
Joined: Dec 2004
Location: Fort Worth
TDKPE said:
My dad had that same blade on his 50's Craftsman TS. It's the only blade that saw has ever had. My 1952 catalog lists it as p/n 9A4943, and touts its safety aspects, and that it can't grab stock and kick it back to the operator. It sold for $12.95, which would be something like $117 in today's dollars.
That was probably the catalog he bought his TS from, by the way.
What's amazing is that when you consider the inflation like that the blades we get now at basically the same price are light years better. It's an incredible value over what they were in the past.
Some things like that have gotten way better and way way cheaper other things not so much.
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
It would rip fine, crosscuts would be a little rough. Wonder if they offered more teeth and some offset in a set. Back then a "combo" blade might have seemed odd, they would have used blades more specific to the job.
Worst thing they can do is cook ya and eat ya
GW
Posts: 2,078
Threads: 1
Joined: Feb 2009
Location: Mechanicsville, Md
I have talked about an 8 tooth blade before on here. We used them where I used to work for rough ripping thicker stock, at least 1 1/2" thick. It leaves a very rough edge but was very good at ripping stock to rough size. This was done to break down a wide board into smaller width pieces (over size) and then machine them to final size. Hope this helps.
I no longer build museums but don't want to change my name. My new job is a lot less stressful. Life is much better.
Garry
Posts: 712
Threads: 0
Joined: Feb 2013
I really miss the Sears catalog.
It was like a early IPad
You could waste hours looking.
Rusty
Poppa's Woodworks
Posts: 691
Threads: 0
Joined: Apr 2003
I had one, used it so cut aluminum plate
