Woodnet Forums › › Active › Woodturning v
Yarn Bowl
Thread Modes
Yarn Bowl
Splinterz25 Offline
Member
Posts: 514
Threads: 0
Joined: Aug 2017
Location: Pleasant Valley MD.
#9
02-04-2018, 12:45 PM
10" x 5" White Oak Yarn bowl 
Made this for my honey.


Attached Files Image(s)
   
   
   
Jack Of All Master Of None 

https://www.facebook.com/serenityartisans/

My 16' Cedar Canoe build  http://www.clcboats.com/forum/clcforum/t...28426.html
Website Find
Reply
MidwestMan Offline
Geezer in Training
Posts: 3,186
Threads: 0
Joined: Feb 2001
Location: Near Chicago
#10
02-04-2018, 01:17 PM (This post was last modified: 02-04-2018, 01:18 PM by MidwestMan.)
Looks great. I think the undercut rim is excellent. I've never understood the slot in the side of yarn bowls. Does anyone know why the slot is there?
Find
Reply
Dusty Workshop Offline
Member
Posts: 4,787
Threads: 0
Joined: Jan 2005
#11
02-04-2018, 03:07 PM
I assume that the slot is easier to 'load' the yarn through rather than just a hole drilled in the side of the bowl. Perhaps less friction too. Someone in the knitting forum downstairs might know.

I like the form of this bowl. What did you use to cutting the slot?
The ALS Association
Lewy Body Dementia Association
Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,545
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#12
02-04-2018, 04:09 PM
(02-04-2018, 01:17 PM)MidwestMan Wrote: Looks great. I think the undercut rim is excellent. I've never understood the slot in the side of yarn bowls. Does anyone know why the slot is there?

so you can pull the yarn out without the ball of yarn unravelling.    I made my MIL one a while back.  A couple of her friends have asked where she got it.  I have some walnut that's about the right size for a yarn bowl.  I may make a couple and see if a local shop here will sell them.
Website Find
Reply
sniper Offline
Pirate from way back
Posts: 22,408
Threads: 0
Joined: Dec 2004
Location: Monrovia, AL
#13
02-04-2018, 05:43 PM (This post was last modified: 02-04-2018, 05:43 PM by sniper.)
That is really neat. I may make one for my daughter. How did you make the slot?
Find
Reply
crokett™ Offline
Finally Off HoneyBooBoo's list
Posts: 36,545
Threads: 3
Joined: Nov 2004
Location: RTP, NC
#14
02-04-2018, 07:15 PM (This post was last modified: 02-04-2018, 07:16 PM by crokett™.)
(02-04-2018, 05:43 PM)sniper Wrote: That is really neat.  I may make one for my daughter.  How did you make the slot?

I've made them with a dremel. I cut them after the turning is finished but before final sanding.
Website Find
Reply
Splinterz25 Offline
Member
Posts: 514
Threads: 0
Joined: Aug 2017
Location: Pleasant Valley MD.
#15
02-04-2018, 10:23 PM (This post was last modified: 02-04-2018, 10:24 PM by Splinterz25.)
Thank you guys I cut the slot w/ a jig saw and a fine tooth blade, sanded it w/ a dowel wrapped in self sticking sanding paper.
Jack Of All Master Of None 

https://www.facebook.com/serenityartisans/

My 16' Cedar Canoe build  http://www.clcboats.com/forum/clcforum/t...28426.html
Website Find
Reply
sniper Offline
Pirate from way back
Posts: 22,408
Threads: 0
Joined: Dec 2004
Location: Monrovia, AL
#16
02-06-2018, 10:17 PM
(02-04-2018, 10:23 PM)Splinterz25 Wrote: Thank you guys I cut the slot w/ a jig saw and a fine tooth blade, sanded it w/ a dowel wrapped in self sticking sanding paper.

Thanks. I was thinking a jigsaw, but wanted to ask in case you had a better way.
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.