Zero clearance
#11
I'm having brain freeze. If I make a zero clearance saw table throat plate at 45 degrees what happens when I raise and lower the blade.]
Reply
#12
Blade will bind up
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#13
There's some information here....

https://www.ncwoodworker.net/forums/show...hp?t=35570
Reply
#14
You'll be fine, I keep one cut at 45º. You just have to make sure your blade is at 45º when you raise and lower it.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#15
(02-23-2018, 06:39 AM)fredhargis Wrote: You'll be fine, I keep one cut at 45º. You just have to make sure your blade is at 45º when you raise and lower it.

But it won't be a zero clearance on the next cut.

I have two throats.  One for angle cuts.  They replace easily on my Delta.
No animals were injured or killed in the production of this post.
Reply
#16
(02-22-2018, 06:21 PM)sussertown Wrote: I'm having brain freeze. If I make a zero clearance saw table throat plate at 45 degrees what happens when I raise and lower the blade.]

 If you have a cabinet type table saw the blade rises and lowers along the blade axis.   Tilt the blade at 45 and raise it and see if it extends along the 45 degree angle.  If it does, it will not bind when changing the elevation.   Roly
Reply
#17
(02-23-2018, 08:30 AM)Roly Wrote:  If you have a cabinet type table saw the blade rises and lowers along the blade axis.   Tilt the blade at 45 and raise it and see if it extends along the 45 degree angle.  If it does, it will not bind when changing the elevation.   Roly

You are not accounting for the thickness of the throat plate.  The axis is at the surface of the plate, not any deeper.

You will have to cut another slot into the throat plate at the 45 degree angle.  If you tilt the blade with your pre-made zero clearance throat plate while the blade is raised you will put the blade in a bind.

Its best to have 2 plates.
There are 10 kinds of people in the world, those who know binary and those who do not.
Reply
#18
Like Cooler, I have multiple ZC plates that I made. Making one is just as easy as six...six just takes a bit longer.

One for 90*, one for 45*, one for dados, and a few extras for "off" angles or other dado sizes.
Semper fi,
Brad

Reply
#19
(02-23-2018, 09:40 AM)s9plus20 Wrote: You are not accounting for the thickness of the throat plate.  The axis is at the surface of the plate, not any deeper.

You will have to cut another slot into the throat plate at the 45 degree angle.  If you tilt the blade with your pre-made zero clearance throat plate while the blade is raised you will put the blade in a bind.

Its best to have 2 plates.

May be I misunderstood the question.   If you have a 45 degree zero clearance throat plate installed, you can raise and lower on a cabinet table saw without binding.    If you install a 90 degree throat plate with the blade lowered all the way and raise the blade it will cut a new slot at a 45.   It will no longer be a zero clearance plate.    I am not sure how the blade raises and lowers on a contractor type saw.   Roly
Reply
#20
(02-23-2018, 08:14 AM)Cooler Wrote: But it won't be a zero clearance on the next cut.

I have two throats.  One for angle cuts.  They replace easily on my Delta.

Yes it is, i only use for 45º cuts, and the blade has to be fully retracted to remove the insert.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply


Forum Jump:


Users browsing this thread: 4 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.