Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
I have a Steel City 17" drill press. It's a great machine, but the chuck jaws are extremely hard to open and close by hand. I don't know why I didn't call them about it when I had the chance, but here I am. Do you think there's anything I can do? Or am I stuck on the tight end of tolerances?
Thanks.
Best,
Aram, always learning
"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery
Web: My woodworking photo site
Posts: 589
Threads: 0
Joined: Jan 2017
Location: Marina del Rey
Replace with a quality chuck.
Wood is good.
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
09-23-2018, 11:29 AM
(This post was last modified: 09-23-2018, 11:47 AM by Aram.)
(09-23-2018, 11:11 AM)ez-duzit Wrote: Replace with a quality chuck.
Thanks. I love an inexpensive solution.
Any recommendations?
Best,
Aram, always learning
"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery
Web: My woodworking photo site
Posts: 1,992
Threads: 1
Joined: Aug 2016
(09-23-2018, 11:29 AM)Aram Wrote: Thanks. I love an inexpensive solution.
Any recommendations? I've heard of Jacobs. That's all I know.
Did you try cleaning it ? May just be hardened grease/wax, cosmoline. Suggest removing chuck and cleaning with something like brake clean or carb cleaner then a little WD 40 to see if it loosens up before replacing. Roly
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
(09-23-2018, 11:38 AM)Roly Wrote: Did you try cleaning it ? May just be hardened grease/wax, cosmoline. Suggest removing chuck and cleaning with something like brake clean or carb cleaner then a little WD 40 to see if it loosens up before replacing. Roly
Thanks. I have brake cleaner. I'll give it a shot.
Best,
Aram, always learning
"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery
Web: My woodworking photo site
Posts: 20,950
Threads: 0
Joined: May 2005
(09-23-2018, 11:38 AM)Roly Wrote: Did you try cleaning it ? May just be hardened grease/wax, cosmoline. Suggest removing chuck and cleaning with something like brake clean or carb cleaner then a little WD 40 to see if it loosens up before replacing. Roly
This ^^^, because the jaws may be sticking to that shipping stuff or crud you've added to the cone or threads over time. The cone itself may be damaged, which would lead me to a new chuck.
My current DP is also a Steel City.
Better to follow the leader than the pack. Less to step in.
Posts: 18,432
Threads: 0
Joined: Jul 2006
Location: Milwaukee area
REMEMBER when you're done cleaning, that if you remove the chuck and want to reinstall, you NEED the tapered surfaces to be clean of all oil before re-seating.
I use lacquer thinner on a rag to clean the male end and same on cotton swaps to clean the female end. I do this 2-3 times and let the solvent flash-off then re-assemble.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Top side of the chuck, where the outside meets the inside, spray some lube of weyhh (what ever you have handy) in there and work it back and forth by hand.
That may/may not clean the crud out and loosen it up.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
Badly hardened metals (Too hard or soft) can deform or break when used and cause this. In this case it is probably a cheap chuck or shall we say...less than quality. Try oiling it first.
Probably, commonly, a broken or deformed tooth on a jaw.
I'd just replace it.
Posts: 12,596
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
09-23-2018, 01:28 PM
(This post was last modified: 09-23-2018, 02:28 PM by fredhargis.)
My Delta DP chuck did that. I tried to repair it, and it didn't work. You should try the oil/cleaner/etc. solutions and if that doesn't work buy a new one. I'll recommend a non Asian chuck, and the one I picked was an LFA. Made in France, they are very good quality and not as expensive as a Jacobs. BTW, if you seach for a Jacobs chuck...you get all the pretenders, and then some. So be careful. The other thing to consider if you buy new is whether you want to convert to keyless. A lot of guys love them, they weren't right for me but may be worth considering. A good one will cost a little more than a good keyed model.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
|