Posts: 2,273
Threads: 3
Joined: Feb 2005
Location: Central America
(02-26-2021, 07:05 PM)Stwood_ Wrote: The problem with cutting distant kerfs, especially deep kerfs, is that you end up with bumps/rises, on the material. It is not a smooooooth bend/arc
I decided to cut the kerfs in my test piece every 4". That bent easily enough and it feels smooth. I need to avoid the finger joints, though, because it failed when one of the kerfs was over it. I'm going to try a shallower kerf so I don't need to make trim to hide the kerfs.
I also tried to cold bend it and I didn't get far before the board gave out at one of the finger joints with a bang!
Posts: 2,273
Threads: 3
Joined: Feb 2005
Location: Central America
Cake. I only had to cut 2/3 of the way down so with the panels in place, you don't see the kerf. Apparently the arc is steeper in the middle so I cut the kerfs 1" apart and as I went out, changed to 2" and finally 3" apart.
Posts: 12,597
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
Glad that worked out, how did you cut the kerfs? Will you be covering it with a piece of trim?
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 2,273
Threads: 3
Joined: Feb 2005
Location: Central America
(02-27-2021, 12:14 PM)fredhargis Wrote: Glad that worked out, how did you cut the kerfs? Will you be covering it with a piece of trim?
I used a speed square and a circular saw set to 1/2". There won't be any trim. To hide the kerf, I will rip off one half of the groove (this is 3/4" T&G flooring) using my track saw to form a rabbet and then hold a decorative panel in place from the back with washers and screws.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
Did you have the finger joints glued when they gave it up, or just a dry run?
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 2,273
Threads: 3
Joined: Feb 2005
Location: Central America
(02-27-2021, 06:37 PM)Stwood_ Wrote: Did you have the finger joints glued when they gave it up, or just a dry run?
The finger joints were already glued up. That's how I bought them from the store.
I just finished up the frame tonight. I forget to leave my two end stiles full height. Oh, well. I formed stub tenons on the ends of my stiles with my track saw, and glued and pocket screwed them into the groove. It's just clamped on there now. I need to work on the panels next. I'm going to kerf the back of my plywood panels, too.
Thanks for all the ideas.
Posts: 706
Threads: 0
Joined: Dec 2011
I'm happy it all worked out. It looks like an attractive piece of furniture. It just goes to show how many different ways there are to reach a final outcome. While there were some "easier" or quicker ways to do it, you worked with the tools you had and made it happen. I'm building a couple of Stickley dressers for my kids and I don't know how many times I imagined a tool that would make a task go much faster (pass-through sander or riser on the bandsaw), but hand tools, time, and some ingenuity have gotten the job done.
May your bar hold many satisfying beverages over the years!
Posts: 2,273
Threads: 3
Joined: Feb 2005
Location: Central America
Posts: 3,545
Threads: 1
Joined: May 2004
Location: Wisconsin
