Posts: 1,612
Threads: 0
Joined: Oct 2008
Putting a Dayton 18" bandsaw back together. Was putting the upper blade guide back on and noticed that both pieces were bent.
They bent, but are still intact, so I have to believe there's some chance of bending them back. Would I be better to bend them back individually or bolt them together and bend them back together? I have to figure they got bent together.
What are these things made out of? Cast aluminum? Pot metal? Whatever it is, it's not magnetic.
Would heat help?
I'm believe that a steady, firm pressure to bend them back would be better than whacks with a hammer.
Anybody ever done this before? Any tips or tricks? I saw an aftermarket set of guides on eBay that said they fit this saw, but I believe they used one of the original guide pieces, so it would have to be straight. And I just ordered cool blocks for the original guides this week, so I'd like to fix them if possible.
Posts: 2,332
Threads: 0
Joined: Dec 2006
Location: virginia beach VA
Since it is not magnetic, I would guess Aluminum, and that it will be easy to crack. I like the idea of bolting them together and applying a clamp and I really like the idea of getting it pretty hot, then applying the pressure gradually.
Posts: 5,421
Threads: 0
Joined: Jun 2001
Location: Troy IL
That aluminum is not going to like being bent back. I would check if it is something you can still buy before you try it.
Life is what you make of it, change your thinking, change your life!
Don's woodshop
Posts: 116,093
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(04-30-2022, 09:07 PM)Woodshop Wrote: That aluminum is not going to like being bent back. I would check if it is something you can still buy before you try it.
...................
THIS!!!!!!!!!!!!!!!
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 1,289
Threads: 0
Joined: Sep 2012
Location: Mobile, Alabama
My first question is: are causing any alignment problems as they are? If they aren't broke, don't fix 'em.
Posts: 3,755
Threads: 0
Joined: Feb 2005
(05-01-2022, 02:51 PM)Willyou Wrote: My first question is: are causing any alignment problems as they are? If they aren't broke, don't fix 'em.
Me too. It a thrust bearing and I have doubts it will cause a problem with that slight of a bend. Unless you have a source for replacements AND it is causing a problem I would leave it alone.
I have found how much a boat is used is inversely related to how much it weighs.
Kudzu Craft Lightweight kayaks
Posts: 1,612
Threads: 0
Joined: Oct 2008
Just wanted to let everyone know that I attempted a fix yesterday afternoon. There was an auction ending last night for a set of replacement guides, so I figured I better hurry up and see if I needed them.
I kept the parts separate. Placed each one securely in a vise. Gave each a few firm raps with a ball peen hammer.
They may not be perfectly straight again, but they're pretty dang close. Looked over each of them carefully and can't see any cracks beginning to form.
May have gotten lucky. Hope to get the rest of the pieces put back on this thing this week.
Posts: 10
Threads: 0
Joined: Feb 2022
(05-02-2022, 11:41 AM)DieselDennis Wrote: May have gotten lucky. Hope to get the rest of the pieces put back on this thing this week.
Yeah, I think you got lucky. FWIW, (and not much, since I'm not a metallurgist), the piece looks to me more like pot metal than aluminum. Apparently the major advantages of pot metal (non-specific zinc alloys) are that it's cheap, melts at a low temp, and makes good (sharply defined) castings. It feels "heavier" (is more dense) than aluminum, and is also non-magnetic. It's not particularly strong and is brittle, like cast aluminum, so it doesn't bend easily.
