Posts: 424
Threads: 0
Joined: Feb 2005
10-24-2018, 12:18 PM
(This post was last modified: 10-24-2018, 12:20 PM by EBamba.)
Been a while since I was last on here. Tried to search but couldn't come up with the correct term.
Scored some prefinshed QSWO door jamb stock, 11 sticks of 10' L x 4.75" W x 1-3/8", along with some 3/4" sticks. Got them for $50. Question is can I run them through my bench-top planer without ruining the blades? One side is prefinshed and the other side isn't.
Posts: 333
Threads: 0
Joined: Dec 2005
I've planed painted boards before without any issue, I think you'll be fine.
Posts: 12,463
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
The more common answer is that it will dull the blades. I've only done very small amounts so can't testify with any degree of certainy. But if it dulls your blades, so what...have them sharpened. The finishes used in some pre finished applications is very tough....and may well have you changing the blades.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 424
Threads: 0
Joined: Feb 2005
Thanks for the replies. Yes, the appropriate concern is dulling the knives. The planer is a Delta bench-top model with I presume, disposable knives. So if I just planed the unfinished side, should I be concerned with destabilizing the thick QSWO stock? Need to remove two shallow vent ridges that run the length of the stock.
Posts: 12,463
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
That would be no problem (with the planer) but those grooves are usually 1/8" deep or so, will the stock still be usable if plane it down?
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 1,590
Threads: 0
Joined: Aug 2009
Location: Manassas, VA
My initial thought is that if it's an aluminum-based finish then it might dull steel blades. Carbide would be better. If it's lacquer, then there's probably no real concern regardless.
Posts: 13,389
Threads: 4
Joined: Jun 2007
Location: New Jersey
When I had a similar planer, I always saved the dull blades for jobs like this one. The finish won't ruin them, but will dull them up.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 424
Threads: 0
Joined: Feb 2005
(10-24-2018, 01:40 PM)fredhargis Wrote: That would be no problem (with the planer) but those grooves are usually 1/8" deep or so, will the stock still be usable if plane it down?
Should be fine. Thickness of the stock is about 1-3/8" measured to the bottom of the groove. I'll be using it for a table top.
Posts: 424
Threads: 0
Joined: Feb 2005
(10-24-2018, 02:02 PM)FS7 Wrote: My initial thought is that if it's an aluminum-based finish then it might dull steel blades. Carbide would be better. If it's lacquer, then there's probably no real concern regardless.
Not sure what type of finish. Looks and feels similar to prefinshed Baltic birch ply used for making drawers. I may leave the finish and make it the bottom of the table top.
Posts: 1,570
Threads: 0
Joined: Jan 2014
10-24-2018, 03:15 PM
(This post was last modified: 10-24-2018, 03:16 PM by brianwelch.)
(10-24-2018, 03:06 PM)EBamba Wrote: Should be fine. Thickness of the stock is about 1-3/8" measured to the bottom of the groove. I'll be using it for a table top.
Could you just plane the unfinished/grooved side and leave the pre-finished as the underside/unexposed? Or is that a little "tacky"?
Oops, looks like you beat me to it