cutting rafter help
#11
I'm making a lean to greenhouse. The highest wall is 97 1/8" high. The outside wall (low eve) is 84" high. Adjusted run is 98". I want my pitch at 2:12 but I can't get the speed square to pivot to 2" on a 2x4 rafter. Giving the height of the 2 walls, what should the pitch be? And if I can keep the 2' pitch, what would be the angle of the plumb cut? 

I bought a construction calculator because the math involved was making my head spin.

Jim
Reply
#12
If one wall is 8' high (or close) and the other wall is 7' high, and there's 8' (or close) in between them, then the pitch is going to be 1 1/2:12.

I came up with 7 degrees for the plumb cut (or 83 degrees, depending on what you measure from).
Reply
#13
(05-22-2020, 12:09 PM)DieselDennis Wrote: If one wall is 8' high (or close) and the other wall is  7' high, and there's 8' (or close) in between them, then the pitch is going to be 1 1/2:12.  

I came up with 7 degrees for the plumb cut (or 83 degrees, depending on what you measure from).
Thank you sir. I also came up with 1 1/2:12 pitch but rounded up to 2 thinking it would simplify things. 

Jim
Reply
#14
Yeah, your back wall should be 100 5/16" for a 2:12.  Plumb cut is 9.46*
"This is our chance, this our lives, this is our planet we're standing on. Use your choice, use your voice, you can save our tomorrows now." - eV
Reply
#15
https://www.blocklayer.com/roof/raftereng.aspx
Reply
#16
(05-23-2020, 11:28 AM)srv52761 Wrote: https://www.blocklayer.com/roof/raftereng.aspx

I used blocklayer extensively a couple years ago when I built roofs for a pair of buildings, 12x32 and 16x16.  Can't tell you how many times I'd print something out, walk out to my project and get to work.  Both roofs came out great as a result.
"Yes, of course duct tape works in a near-vacuum. Duct tape works anywhere. Duct tape is magic and should be worshiped." Andy Weir (in his book The Martian)
Reply
#17
(06-05-2020, 08:46 AM)kdouglaslee Wrote: I used blocklayer extensively a couple years ago when I built roofs for a pair of buildings, 12x32 and 16x16.  Can't tell you how many times I'd print something out, walk out to my project and get to work.  Both roofs came out great as a result.

The rafters turned out ok for a rookie. I'm sure I would do better if I have to do more. The birds mount was the big pain Thanks
Reply
#18
(06-05-2020, 09:22 AM)Halfathumb Wrote:  The birds mount mouth was the big pain Thanks


Did you make a pattern, to use for marking all the rafters?
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#19
Actually that is a very good web site for rafter's, it takes a bit to understand just what they are saying, for instance to find out the pitch of a roof they give a dimension of 400 and 1200 which really means 4'' or inches of rise and 12" inches of run which is what we normally think of. But really it is a very good web site. Just wondering why you thought you had trouble with the birds mouth cut, making the cut or understanding it? 
Smile
Reply
#20
(06-06-2020, 09:09 AM)bgosh Wrote: Actually that is a very good web site for rafter's, it takes a bit to understand just what they are saying, for instance to find out the pitch of a roof they give a dimension of 400 and 1200 which really means 4'' or inches of rise and 12" inches of run which is what we normally think of. But really it is a very good web site. Just wondering why you thought you had trouble with the birds mouth cut, making the cut or understanding it? 
Smile

I didn't make template for the birds mouth, I certainly wish I would've. I understand it but just got sloppy cutting them. I'll certainly know better if there's a next time.

Thanks everyone.

Jim
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.