Woodnet Forums › › Active › Woodworking Power Tools v
sanding mop

▼
TimPa Offline
Member
Posts: 5
Threads: 0
Joined: May 2013
#12
07-10-2015, 10:53 AM
does anyone have experience using a sanding mop or similar device for sanding routed profiles (ogee)?

looking for info like good quality models, grit, etc.?
thanks
Find
Reply
▼
fredhargis Offline
Member
Posts: 12,644
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
#13
07-10-2015, 11:36 AM
I bought one from Klingspor and chucked in my drill press to sand some factory made balusters I was installing in my last house. It didn't seem to do much at all, I was pretty sour on it. I'm thinking I didn't know what to expect.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Find
Reply
▼
Joe K1 Offline
Member
Posts: 322
Threads: 0
Joined: Aug 2005
#14
07-10-2015, 01:21 PM
Similar experience with the sanding mop. Put it in a box about 8 years ago and labeled it - sanding solution in search of a application. Opened the box once since.
Find
Reply
nicobie Offline
Member
Posts: 478
Threads: 0
Joined: Dec 2004
Location: Central coast CA
#15
07-10-2015, 01:42 PM
Sand o flex with 60 grit slit sand paper works pretty good. The end result is closer to 100 grit.
Find
Reply
Scoony Offline
Honored Veteran
Posts: 6,122
Threads: 0
Joined: Jan 2006
Location: Central Kentucky
#16
07-10-2015, 02:34 PM
I have the sanding mop and find it helpful to soften up edges and sand small curvy parts.

I have the rubber grommets in mine which seems to help spread the sanding flaps.
Find
Reply
SceneryMaker Offline
The Quiet Member
Posts: 4,434
Threads: 0
Joined: Oct 2008
Location: Central Indiana
#17
07-10-2015, 04:28 PM
I have and use the Klingspor version with 120 grit in it to get a finishable surface after the router. I found it helps to spin it pretty fast.

See linky for the one I have and like.
We do segmented turning, not because it is easy, but because it is hard.
Find
Reply
jteneyck Offline
Member
Posts: 12,999
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
#18
07-10-2015, 06:29 PM
If you have a lot of molding to do you need a serious solution. Linky.

John
Website Find
Reply
▼
JerGar Offline
Member
Posts: 1,382
Threads: 0
Joined: Apr 2009
#19
07-10-2015, 08:11 PM
jteneyck said:


If you have a lot of molding to do you need a serious solution. Linky.

John



My Sand-Rite comes in handy,is used a lot.

Find
Reply
▼
TimPa Offline
Member
Posts: 5
Threads: 0
Joined: May 2013
#20
07-13-2015, 08:04 AM
thank you for all of the replies. great info - i wasn't aware of the sand o flex, flap wheel, or quad cutters. i just ordered 2 new whiteside bits too darn
Find
Reply
Steve N Offline
Member
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
#21
07-10-2015, 07:11 PM
TimPa said:


does anyone have experience using a sanding mop or similar device for sanding routed profiles (ogee)?

looking for info like good quality models, grit, etc.?
thanks




Look like a long time member, first time poster, welcome.

John's suggestion can work, how big is the detail on the Ogee? Are there other profiles? Biggest question is how many feet to do?

Other possibilities are.

I have had splendid success with these, better on harder woods than soft.









They come in most profiles, and because of more cutters hitting the stock the metal/carbide gets less heat = longer lasting than 2 and 3 wing cutters.

For softer stuff I just use a sanding sponge cause on the flaps I have seen detail destruction.
Worst thing they can do is cook ya and eat ya

GW
Find
Reply
Thread Modes
sanding mop


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.