Posts: 13,412
Threads: 4
Joined: Jun 2007
Location: New Jersey
I used 3/4 cabinet grade domestic plywood, with cherry top fence and runner for the chute slot. Dead on. I really don't think it matters much what you use, just not Chinese ply.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 6,678
Threads: 1
Joined: Jan 2003
Location: Southern California
I used some left over maple veneer ply for both layers with an 18" Veritas track. I'm going to build another board - only set up for miters this time. Whatever ply I have will be used for the base and maybe the top or maybe MDF. I consider shooting boards to be precision instruments so I try not to ding them up.
Thanks, Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
-- Soren Kierkegaard
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
Worst thing they can do is cook ya and eat ya
GW
Posts: 22,682
Threads: 0
Joined: Oct 2007
Location: Burlington, North Carolina
My $0.02 is that the materials don't really matter so long as they are seasonably stable.
Scrap cabinet ply or even MDF would be fine.
Posts: 10,717
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
BB is fine. That's the material I used for my base. My fence is also BB, faced with hard maple. My fence is removable and therefore replaceable.
Still Learning,
Allan Hill
Posts: 10,118
Threads: 0
Joined: Sep 2006
Location: South Alabama
Any good-quality plywood works just fine.
Heck, even a good, stable hardwood could work okay. I've seen a really nice one made entirely from mahogany off-cuts.
Steve S.
------------------------------------------------------
Tradition cannot be inherited, and if you want it you must obtain it by great labour.
- T. S. Eliot
Tutorials and Build-Alongs at
The Literary Workshop
Posts: 7,008
Threads: 0
Joined: Aug 2004
Location: Perth, Australia
JR1 said:
I built a small shooting board with ¾" MDF on ply base and it's OK. But I'm building a larger board using the 24" Veritas® Shooting Board Track and want something better than MDF. I'll likely use BB for the base but would like something lighter and not easily dinged instead of MDF.
Don't bother unless it is Jarrah ...
... except if you can make it out of cast iron ...
Seriously, you can build a shooting board out of anything, and it will work if constructed carefully. However, if you really want a shooting board that is a pleasure to use and will last, treat the venture as fine furniture and construct if from a decent hardwood. Keep the design simple, make the fence adjustable (because they wear and go out-of-square). Try to use quarter sawn woods if you can (the base of the one above is quarter sawn Tasmanian Oak). An alternative is to use veneered plywood lined with hardwood on the edges that will take the knocks and wear. That will be very stable, and can look the part.
Regards from Perth
Derek
Posts: 8,963
Threads: 0
Joined: Sep 2010
Thanks everyone! The installation instructions don't specify a material, although the video looks like they used ply. Colombia forest products is ½", BB ply is 12mm so it should work. I'm going to take Dereck's advise and put a hardwood edge on it after I try an experiment in the way I build it. If it works I will post pics if not I will make it conventionally and post pics.
Hopefully it will warm up above freezing so I can give it a try soon. Tanks again!
homo homini lupus
"The best lack all conviction, while the worst are full of passionate intensity." Yeats
Si vis pacem, para bellum
Quodcumque potest manus tua facere instaner opere Ecclesiastes
