#20


A friend wants me to build a Oak microwave hutch for him.
He wants it basically 4' wide and around 7' tall.
Is it safe to have only 2 doors above the m/w say
22" wide and 30" tall?

Thinking 2 to 2.5" stiles with a horizontal center rail.
Or should I go 3 door across.
Blum Blumotion hinges

Thoughts

Thanks in advance,

Forest
You have the right to remain silent. Anything you say will be misquoted- then used against you.
Reply

#21
Forest said:

He wants it basically 4' wide and around 7' tall.




That's gonna be a monster...and heavy.

I think I would consider something like bridle joints for the door frames if you only go with two doors. Remember, a door or framed panel gets it's strength from the frame, not the panel (unless you are gluing in a plywood panel).
If I had 8 hours to cut down a tree, I'd do it in 15 minutes with a chainsaw and drink beer the other 7:45 hrs.
Reply
#22
2 doors shouldn't be a problem.
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#23
I built a pair of pantry cabs in my last home. The doors were 96" tall and 24" wide. Made of steamed European beech for both frame and panel. Stub tenons, very typical wood doors with a mid rail.

I did use three cup hinges per door to keep them from bowing top to bottom, but in every way they were successful.

Ralph
Ralph Bagnall
www.woodcademy.com
Watch Woodcademy TV free on our website.
Reply
#24

It is LARGE.
I will be building it in 2 sections to stack later.
Still it's over 2 sheets of 3/4 ply and solid boards.
Plan on 2" face frame stiles to reduce door size.
Is 2.5" doors overboard?

Thanks to all inputs so far !

Forest
You have the right to remain silent. Anything you say will be misquoted- then used against you.
Reply

#25
are the doors overlay or inset? will the cabinet have a face frame or will you mount the doors euro style onto the edged plywood box?

for doors that big, i'd consider doing 2 1/4" or 2 1/2" rails and stiles. are you doing cope and stick for the doors? flat panel or raised panel?

one more thing.. you could use 2 1/2" rails and stiles, but the center separating rail could be thinner. that often looks quite nice to change the proportions a bit.
Reply

#26
I am doing about 1/4 " overlay to a face frame
M+T or could do bridle
1/4 " plywood panel

Forest
You have the right to remain silent. Anything you say will be misquoted- then used against you.
Reply
#27
Forest said:



It is LARGE.
I will be building it in 2 sections to stack later. good plan
Still it's over 2 sheets of 3/4 ply and solid boards.
Plan on 2" face frame stiles to reduce door size. fairly typical
Is 2.5" doors overboard? if you account for the sticking it is not. That gives a 2 1/8" face on the stiles and rails Even if the doors are T&G that is not too much for a cabinet that large

Thanks to all inputs so far !

Forest


Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future  John F. Kennedy 



Reply
#28
I just built a locking saw till. The raised panel door is 40" tall and 30" wide (three hinges). My rails and stiles are 3" wide, and visually they look very small to me. They are plenty strong though.
Reply
#29
Your plan for rail and stile widths are fine. If you are making the doors from solid wood and want to eliminate cupping and warp, then use quartersawn lumber. I would use quartersawn or riftsawn for the frame too.
mike
Reply
Door size


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.