Disk Sander

[Peter Tremblay]

I've been wanting to turn my lathe into a disk sander for a while.

So I bought a 10" disk that is designed to be used on a table saw to turn it into a disk sander.

My question now is how can I mount it to a 1" x 8 tpi faceplate?

I want it to be very close to perfectly centered.

Any ideas?

If I could figure out a way to get it centered I'd probably epoxy it in place. Maybe even drill and tap a few machine screws while leaving the face of the disk flush.

Any thoughts or advice are appreciated.

[AHill]

Find the center of your disk. Measure the diameter of the outer rim of your faceplate. Divide by 2 to get the radius. Set your compass to just a hair over the radius and draw a circle on your disk. Now, get some double sided sticky tape and mount your faceplate so that the radius is even all the way around. Use a vix bit or something similar to pre-drill your holes for your faceplate. Dismount the faceplate, remove the tape, and remount with screws.

[Mr_Mike]

Peter Tremblay said:

---

I've been wanting to turn my lathe into a disk sander for a while.

So I bought a 10" disk that is designed to be used on a table saw to turn it into a disk sander.

My question now is how can I mount it to a 1" x 8 tpi faceplate?

I want it to be very close to perfectly centered.

Any ideas?

If I could figure out a way to get it centered I'd probably epoxy it in place. Maybe even drill and tap a few machine screws while leaving the face of the disk flush.

Any thoughts or advice are appreciated.

---

Seems to me you want a 1" x 8 tpi to 5/8 arbor adapter. Though, I have no clue where to find one.

Otherwise, I'd buy a large diameter faceplate and face with an MDF disk that is trued after mounting.

[sniper]

Mr_Mike said:

---

Otherwise, I'd buy a large diameter faceplate and face with an MDF disk that is trued after mounting.

---

A little late, but this is what I did except I glued a piece of 3/4" ply to the 3/4" MDF to give the screws a little more to grab onto. I ordered [url=http://smile.amazon.com/Steel-Wood-Lathe-Plate-Threaded/dp/B003THWJ9Q/ref=sr_1_1?s=hi&ie=UTF8&qid=1460408908&sr=1-1&keywords=6"+Steel+Wood+Lathe+Face+Plate]this face plate[/url] (mine was 1 1/4" x 8tpi) from amazon and it works great.

Sorry I can't be more help. Good luck

[MichaelMouse]

There's a centered hole in the sanding plate. Glue a thin piece of wood to your faceplate, turn the edges off, leaving the center proud, and of the diameter of the hole in the sanding plate. Center and glue.

[Peter Tremblay]

MichaelMouse said:

---

There's a centered hole in the sanding plate. Glue a thin piece of wood to your faceplate, turn the edges off, leaving the center proud, and of the diameter of the hole in the sanding plate. Center and glue.

---

Thanks, that's a good idea.

Any suggestion for the glue? Type of wood?

[MichaelMouse]

I used some ~1/4" bass. Glued my 1" square with ca, marked my approximate arbor and scraped slowly with a snipped nail in a stick. Little bit of taper will allow positioning precisely to center and a whack or two to get the bass crushed for the final modification.

[theeviltwinn]

Metal spinning technique. Faceplate in the headstock. Piece of wood in the tailstock. Sanding plate between the two. Once centered drill and tap some screws to hold it.

https://www.youtube.com/watch?v=W7QB0-AlwtI

Skip to the 4 min mark

Twinn

[chips ahoy]

Peter
I took a 3/4" piece of plywood and attached a 5" face plate to it. I made it slightly larger than 10" so I could true it up on the lathe. You can buy various grits of 10" paper with a sticky back from Lee Valley. Works great.

Mel

[Tony Turner]

When I did my 16" aluminum disc I put the disc in my large Cole jaws, marked it and it turned out very well. Good luck. Tony