Posts: 64,669
Threads: 3
Joined: Feb 2007
Location: Merryland
Are they joists or rafters/trusses?
If they're joists, fir them out. You might glue the firring strips, particularly on the thicker ones so your DW screws don't pull it off. Maybe use a longer screw too.
Is the old drywall off? If it's trusses, sometimes trusses lift (google rafter lift) and insulation gets between the rafter and the drywall so the rafters can't go back down and a gap is left between the truss and drywall. You'll usually see a lot of nail-popping in those areas. If it's trusses, you aren't screwing in the perimeter anyway so you'll only need to fir out the area where the screws will be and not within about a foot of the edge.
Posts: 12,237
Threads: 0
Joined: Sep 2003
Location: Matawan NJ
Drywall is off and they are joists.
So you're saying to fur out the whole ceiling like this? If so, do I then connect the ceiling HVAC registers and exhaust fan to the furring strips instead of the joists?
![[Image: IMG_4608.JPG]](http://4.bp.blogspot.com/-9_cdUh2YMiI/UFiB40XCa2I/AAAAAAAAAJc/wMx4VdsE6VE/s1600/IMG_4608.JPG)
Posts: 5,733
Threads: 2
Joined: Dec 2004
Location: Fort Worth
1930 house you don't have trusses. Just shim it and drywall it and run screws as usual. The drywall guys use cardboard shims that are precut as spacers.
You can run furring strips and just level them if you want. But please for the love of electricians ans hvac guys never do an entire house with furring strips. You can do it in your bathroom but... Framers that do this are jerks and they hate the other trades. The problem is when you need to go in later and add lights or hvac ducts you have no way to know where the ceiling joists are. You end up hacking at the ceiling and then the drywall guy has to redo the whole ceiling to get the texture to look right then it doesn't match the walls...
Which is the other huge no no in construction. Never ever ever ever texture walls. They are impossible to repair without skim coating the entire wall or room. Anyone can make a wall smooth but very few can match texture.
Posts: 12,237
Threads: 0
Joined: Sep 2003
Location: Matawan NJ
I'm not going to do the drywall myself. Is the shimming something a drywall contractor would normally do? I haven't yet talked to them.
Posts: 35,172
Threads: 0
Joined: Oct 2003
A buddy of mine is a pretty high end general contractor and is working on a million dollar renovation near Lake Michigan in the northern suburbs of Chicago. Part of the foundation in the duplex (yeah, two $1 million dollar units in a duplex) has sagged enough that he needed to level the floor. His solution, which was approved by the local building inspector, was to slave 2x10's to the floor joists to level things out.
Since this is a ceiling, you won't need the strength of a 2x10, but perhaps you can use 2x's to level this ceiling. That would be a lot easier and more solid than furring strips, IMO.
Blaine
Posts: 12,237
Threads: 0
Joined: Sep 2003
Location: Matawan NJ
I was hoping I could just shim up the 2 bad ones and that the others within 1/4" or so was good enough.
It looked flat before I took it off, but there were 2 layers of sheetrock on the ceiling.
Posts: 29,861
Threads: 0
Joined: Jan 2008
Location: Mid-MI
(03-09-2017, 08:57 AM)APZ Wrote: I'm not going to do the drywall myself. Is the shimming something a drywall contractor would normally do? I haven't yet talked to them.
Depends... I hired a guy to hang the drywall in the basement due to being able to sight it. We discussed it, I told him I didn't want to see any waves in the ceiling. He said "No problem"
Mark
I'm no expert, unlike everybody else here - Busdrver
Nah...I like you, young feller...You remind me of my son... Timberwolf 03/27/12
Here's a fact: Benghazi is a Pub Legend... CharlieD 04/19/15
Posts: 1,531
Threads: 0
Joined: Jan 2007
It is such a small area. I would sister some 2X 4's against each joist. Make sure they are straight. Make sure any lights or duct work fits. Mark these new studs so that is what you screw to. Level as level can be. If you try to shim you have to see if the entire joist is equally out and there maybe low spots. It is not structural and is just for a ceiling. This is the way I would correct it.
John T.
Posts: 5,733
Threads: 2
Joined: Dec 2004
Location: Fort Worth
(03-09-2017, 08:58 AM)Blaine Wrote: A buddy of mine is a pretty high end general contractor and is working on a million dollar renovation near Lake Michigan in the northern suburbs of Chicago. Part of the foundation in the duplex (yeah, two $1 million dollar units in a duplex) has sagged enough that he needed to level the floor. His solution, which was approved by the local building inspector, was to slave 2x10's to the floor joists to level things out.
Since this is a ceiling, you won't need the strength of a 2x10, but perhaps you can use 2x's to level this ceiling. That would be a lot easier and more solid than furring strips, IMO.
Blaine
That's a typical way to fix a sagging floor. Just sister another beam along side and go on. Unfortunately many energy and material efficient houses suffer from poor framing to get the desired result. Long spans on small lumber and many running 19.2 or 24" oc floor framing. It meets code but it isn't going to stay flat.
The drywall guys can do it but many wont. The better the framing is before they get there the better the end result.
