#16
It's time to begin building the drawer that will fit this table ...


[Image: TheBevelLiesInTheDetails_html_m2ae8de9d.jpg]


I must say up front that this is the strangest drawer I have built to date. It is definitely the longest. In fact, I dare anyone to have built a longer drawer (it's about 1200mm long, or nearly 4 feet in the old money). 


It is also the ugliest drawer I think I have built - however, that is partly to be expected as it is a hidden drawer, that is, it must blend in with the apron so that no one knows its there (no telling now).


The drawer sides are made from the same timber that will be used for the table top, West Australian Sheoak. This is a pink-brown wood with a fine figure (similar to Lacewood). Here is the slab I started with ...


[Image: SofaTableAprons_html_m66b1e7ca.jpg]


The drawer is slim - more like a tray. There is just 40mm for the drawer, and this will convert to 30mm of head room after the drawer bottom is added.


Below is a picture of the drawer sides fitted to the interior ...


[Image: 1a_zpshmfudk8f.jpg]


They run below the Domino-buttons, which double to ensure that the drawer will not tip when extended.


The next step was to glue up the drawer bottom ...


[Image: 3a_zpsmk2wju0b.jpg]


Since the drawer is fairly narrow (about 210mm/8 1/4"), it was tempting to simply use a single board and run it with the grain down the length of the drawer. However I know that this will create problems when the wood expands and contracts. Drawer bottoms need to run across its width. Consequently, boards were sawn and glued together for this purpose. The thickness of the drawer bottom is 1/4".


Below is the drawer bottom being trued on one length and one width. The remainder will be sized at the end.


[Image: 4a_zps4osvnjnq.jpg]


Drawer Slips


The drawer sides are 3/8" thick, which is too thin for grooves. Consequently, the drawer bottom will be attached with slips. This is how they were made ...


The first step was to score the bottom of the slip. They are being made from the top down, and reverse-engineered ...


[Image: 5a_zpshrrrwjkv.jpg]


There is a 5mm space to the next line (the height above the drawer blade) ...


[Image: 6a_zpsyyxmedvk.jpg]


The groove is going to be 3/16". The drawer bottom will be rebated 1/16" along the sides to fit.


[Image: 7a_zpsyd6iku86.jpg]


Plough the groove ...


[Image: 8a_zpshgv9qgln.jpg]


[Image: 9a_zps48wb7j2e.jpg]


Chamfer the edges ...


[Image: 10a_zpskqogijss.jpg]


I scraped a slight curve on the inside ...


[Image: 11a_zpssylpgttn.jpg]


... and then ripped them free on the table saw ...


[Image: 13a_zpsmvfgscsx.jpg]


Back to the drawer


I warned you that this was a weird looking drawer. Here is the drawer front - ploughing the front groove. This has to allow for the lower- and upper overlay to match the apron ...


I will not show you boring pictures of dovetailing, however this is a how the drawer front is constructed ...


[Image: 14a_zpspxfsfgfm.jpg]
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply

#17
[Image: 15a_zpsw9fygbxa.jpg]


With the sides joined, this is how the drawer front looks ...


[Image: 16a_zpszvmvoxix.jpg]


From this inside ...


[Image: 17a_zpsksej4tdf.jpg]


The through dovetails at the rear of the drawer look like this (all very rough at this stage) ...


[Image: 6a_zpsmg4xq0xk.jpg]


I planned that the drawer would have a working depth of 250mm (10"). The drawer back was attached with a though mortice-and tenon ...


[Image: 2a_zpskqcpnm4j.jpg]


[Image: 3a_zpsxy2iia37.jpg]


Of course, I did not think this through, and the lower tenon sits where the slip runs. I had to saw it off and fill the hole. Well, it looks like a double mortice-and-tenon. We are the only ones to know the truth ...


[Image: 7a_zps2ro9tvme.jpg]


Here is a picture of the drawer ...


[Image: 4a_zpsgaspaojj.jpg]


Below is the drawer extended, with a mock up of the top ...


[Image: 5a_zpse4ufhfrk.jpg]


The drawer can extend much further than this without any droop. I am considering another hidden drawer behind this drawer - by adding another divider. This would also add more rigidity (not sure if this is needed).


Finally, here is a picture of the drawer end of the table alongside the sofa table it will replace ...


[Image: 8a_zpszkartrns.jpg]


We'll complete the drawer next time.


Regards from Perth


Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply
#18
Nice work Derek. I always enjoy your builds. Thanks for sharing all the details.
Jim
http://ancorayachtservice.com/ home of the Chain Leg Vise.
Reply
#19
So the section behind the 10" divider is the secret part? Cool! And, that is a strange drawer(s) setup.
Reply
#20
Very nice - as usual! A nice table with elegant lines. Appears as though the Sheoak was a good choice.
Thanks,  Curt
-----------------
"Life can only be understood backwards; but it must be lived forwards."
      -- Soren Kierkegaard
Reply
#21
(06-26-2017, 06:49 PM)hbmcc Wrote: So the section behind the 10" divider is the secret part? Cool! And, that is a strange drawer(s) setup.

Well Bruce, the drawer is secret. Then there is a secret drawer behind the secret drawer.
Smile

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply
#22
(06-26-2017, 11:38 PM)Derek Cohen Wrote: Well Bruce, the drawer is secret. Then there is a secret drawer behind the secret drawer.
Smile

Regards from Perth

Derek
I'd call that a sub-secret drawer.... Or, after the considered second divider ... the sub sub-secret drawer. Cooler than cool! Ya' gotta have fun with your fun times.  Yes, definitely, a secret pencil collection is developing here.
Big Grin 

It's all looking great, Derek.
Reply
#23
A question: When you plough the groove for the drawer bottom in the slips, would it be better to gauge both walls of the groove?
Reply
#24
Bruce, it is not necessary if you are planing with the grain. I only do so if planing into the grain (it is a "dado" when planing across the grain).

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Reply
Sofa Table - part V: A Hidden Drawer


Forum Jump:


Users browsing this thread: 3 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.