#18
Hi all,

Trying to smooth some VG fir to use as window trim.  In the past I have always sanded it but I don't feel like listening to the sander all week.  

I can't get the fir as smooth as I would like and I am looking for some tips. Planes are sharp and pretty well tuned.  Grain changes direction a bit in the fir which I guess is most of the problem.  I can get it smooth but it only feels like 120-150 grit to me.  I would like it a little smoother.  Any tips are appreciated.

Thanks,

John
Follow along on the instantgram:  room_23_woodworks
Reply

#19
I realize this is the hand tool forum but, depending on how much linear footage you have, it may be worth seeing if a local shop rents out sander time, The shop I work in does it all of the time. We have a 3' wide belt sander. Locals are always renting time on it. Just a thought.
I no longer build museums but don't want to change my name. My new job is a lot less stressful. Life is much better.

Garry
Reply
#20
Scraper, after planing.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Reply
#21
A scraper might not work very well. The spring wood, the lighter colored part is very soft compared to the darker summer wood. "Soft" woods do better when sanded. Or machine planed. S2S from the mill is pretty smooth.
Reply
#22
Are you working Doug fir or Hemlock? Are you restoring existing 'fir' trim? If hemlock do what you want. If you sand DF more than a few swipes, there will be a washboard surface caused by variable density (hardness) in the grain. If there is tearout from a plane, the iron is not sharp enough. I can't help with restoration ... other than buy a new house.

You could go through the performance grind of plane, scraper plane, hand scraper and paper up to 220 grit. But, given the amount of surfacing you plan, it might be time for the DeWalt 735. I have the the 734. And, this is your money I am playing with. .... Unless its a couple feet of wood, hand surfacing is for dummies. My ears are shot anyway. You will need to do the final 4 by hand, but it's a dream and your garden will love you.
Reply
#23
IF this trim is to be painted...prime and then sand it back until the trim is smooth, prime again, sand a bit, then paint..

The first sanding is just to remove the "high" spots, second one for final smoothness, before the paint..
Show me a picture, I'll build a project from that
Reply
#24
Thanks for all the replies.  I have gone the sanding route in the past with this trim and gotten a great result.  I want to plane it as a exercise in practice hand planing.  Working slowly towards a hand tools(plus bandsaw) shop.  It is Fir not hemlock and won't be painted.  I am going to finish it with teak oil.  So far I can get reasonable smooth with planes and clean up where needed with a card scraper.  My guess is I will go back to sanding it but I wanted to give planing a try.

John
Follow along on the instantgram:  room_23_woodworks
Reply
#25
Gotcha, now I understand. Question. If you are trying to replicate "older" molding, you might want to remember that those moldings had tool marks all over them. It might add some authenticity to your work.
I no longer build museums but don't want to change my name. My new job is a lot less stressful. Life is much better.

Garry
Reply
#26
Barn wood siding, recycled into a table...
[attachment=3110]
Shelf and the top...
Show me a picture, I'll build a project from that
Reply
Planing VG Fir


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.