Posts: 307
Threads: 0
Joined: Sep 2016
Hard to tell from the photo, but I'd give it a 1/16 on each edge in direction of movement....
Andy
-- mos maiorum
Posts: 29,152
Threads: 1
Joined: Aug 2002
It will need some room for potential movement yes
If it were me I would skip the z clips add a ledge under the frame and rest the top on that. use a flexible sealant to seal the connection but only to keep water and debris out that way if the seal ever needs replaced you can lift the granite out and clean it after cutting the seal
Joe
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
I don't believe the granite is going anywhere (I Googled to see, as I don't have first hand knowledge, and couldn't find a path to follow, wood totally different story.) The wood may move in toward the granite trapping it, and if too tight possibly it could cause a crack. If you allowed the 1/16 to 1/8" around the granite you would be good. If worried about trapping food in the crack, you could caulk it, and it will compress just as it does around windows, and doors.
Worst thing they can do is cook ya and eat ya
GW
Posts: 1,133
Threads: 0
Joined: Aug 2004
No not worried about food getting into the crack. Just want to insure that I don't crack the top because of expansion/contraction.
Posts: 1,998
Threads: 1
Joined: Aug 2016
Is this a 18" square cut into the center of the 34" width ? I am also assuming the the top is made up from boards butted up tight to each other with no room for expansion so you have be be concerned about expansion and contraction across the 18" width, if this is the case along with the fact it is outside, I would think you will need a lot more room in the opening than a 1/8" especially if you have seasons in the area you live. Roly
Posts: 1,133
Threads: 0
Joined: Aug 2004
Yes, it is 18" in the center of a panel that is 34" wide and the boards are glued together. But across the grain, there is only 8" on either side of the granite. It will be outside under a covered porch and will have a cover over the table as well. I would think that 1/16 to 1/8" would be plenty of space for expansion.
Any others have opinions about this?
Posts: 12,888
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
Granite has a coef. of thermal expansion of 4.4 x 10-6 in/in-°F, so your 18" wide piece of granite is going to expand 0.008" total with a temperature change of 100°. I'd say that's nothing to worry about. An 8" wide piece of pine might expand/contract 3/32" seasonally. It'll do that around it's center line but on both sides of the frame; so if you make the frame 3/32" larger than the granite all should be well.
John
Posts: 1,998
Threads: 1
Joined: Aug 2016
The granite is not the problem, the 18" of width across the wood grain is where the expansion and contraction is going to occur. If you place 18" of solid stone in the opening and the wood shrinks to somewhat less than 18" what will happen ? Splits along the grain coming out from the corners of the cutout. I don't know how much room to leave on the width using cypress but it will be more than 1/8" for sure. Roly
Posts: 29,152
Threads: 1
Joined: Aug 2002
18" and 1/8" total clearance will just be fine.
It does not have to be more.
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
