Posts: 545
Threads: 0
Joined: Jul 2007
Location: Harper, Kansas
I'm not sure that you're going to be able to find something like that premade.A local hobby machinist could make those in just a few minutes, though I'm betting he would charge more that what it's worth. My best advice would be to make something out of a hardwood, or better yet some Baltic birch ply or similar.
It's not always the quiet ones who don't have much to say.
Posts: 1,612
Threads: 0
Joined: Oct 2008
(01-15-2018, 12:30 PM)Herb G Wrote: I need some flat steel bars about 1/8" thick, 1" wide, and 12" long with a slot in the middle of the bar, full length.
I need at least 4 or 5 total.
I will attach a picture so you see what I'm talking about.
I don't have a way to make any, or else I would.
I don't want to spend a fortune on them either.
They are only for holding a Mini Gulp dust hood to my lathe.
Here's the hood.
http://www.rockler.com/mini-gulp-dust-hood
Here's the bars. They are in the pic holding the thing to the lathe.
https://www.pennstateind.com/store/DLGULP.html
Do you know what these bars are called & where I can buy some?
I tried McMaster Carr already.
I have angle steel here that has holes drilled in it, but it's not flat & too hard to work with.
Add a zero to your quantity requirements and quote it to a shop with a CNC laser. Can be had quite affordably.
Buy the hardware in bulk and develop a kit for other turners to use to hold their dust shield. Sell down in S&S and take LOYL out for a meal this weekend.
Posts: 162
Threads: 1
Joined: Sep 2017
Posts: 36,538
Threads: 3
Joined: Nov 2004
Location: RTP, NC
you could make them with a 1/2" drill bit and and an angle grinder in not very much time. it would probably take longer to file the edges smooth than it would to cut the slots.
that said, I'd make them out of plywood.
Posts: 36,538
Threads: 3
Joined: Nov 2004
Location: RTP, NC
Probably. Personally, I'd make them out of plywood and use a router to cut the slots and mill the outside profile close, then a sander to finalize the outside profile.
Posts: 29,861
Threads: 0
Joined: Jan 2008
Location: Mid-MI
In the Q&A section of your item, they say Rockler sells an adjustable arm. However, this is all I could find. Nice setup.
http://www.rockler.com/dust-right-lathe-...ion-system
If I were making it myself, I'd think about the slotted angle iron that is used for supporting garage door openers / tracks.
Or just build it out of ply. Or maybe, 1" aluminum flat stock, you don't need slots the full length... a bit of figgerin' and put a couple where you need them. Easy enough to add another if need be.
Mark
I'm no expert, unlike everybody else here - Busdrver
Nah...I like you, young feller...You remind me of my son... Timberwolf 03/27/12
Here's a fact: Benghazi is a Pub Legend... CharlieD 04/19/15
Posts: 7,421
Threads: 1
Joined: Sep 2005
A Manfrotto Magic Arm, a device made for photographers to hold lighting or other equipment in place, can certainly accomplish this task, and probably more sturdily than the steel brackets.
It is discounted to about $100.00. They offer many accessories for this and it has multiple uses. Very sturdy and versatile.
https://www.manfrotto.us/magic-photo-arm...king-lever
![[Image: 1280px-Manfrotto_Magic_Arm.jpg]](https://upload.wikimedia.org/wikipedia/commons/thumb/9/92/Manfrotto_Magic_Arm.jpg/1280px-Manfrotto_Magic_Arm.jpg)
No animals were injured or killed in the production of this post.
