Posts: 1,622
Threads: 0
Joined: Mar 2008
03-09-2018, 11:40 AM
(This post was last modified: 03-09-2018, 12:27 PM by Lynden.)
Posts: 12,606
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
The Triton has an odd feature that compliments table use. It has a sliding cover over the power switch that must be retracted to turn it on. While on, the cover stays in the open position, then when you witch it off, the cover closes. So if you put it in a router table that has an external switch, you think you'll just it the router itself switched on, right? Well, the shaft lock will not engage unless that sliding cover is closed. So you have to turn the router itself off to get the shaft to lock allowing bit changes. If you choose to not use an external switch, you're stuck with sliding that gate open to switch it on under the table. Soem folks have said this isn't a problem, but it would be for me (I have a Triton, but it's dedicated to a certain hand held use). But understand, I'm not suggesting you avoid it.....just be aware of this what might be inconvenience.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 589
Threads: 0
Joined: Jan 2017
Location: Marina del Rey
Probably just needs to have the bearings replaced.
Wood is good.
Posts: 7,421
Threads: 1
Joined: Sep 2005
03-09-2018, 01:46 PM
(This post was last modified: 03-09-2018, 02:13 PM by Cooler.)
I've never understood the whole router table thing. You build or buy a table, then get a lift and add the router and you are into this for over $1,000.00.
That's more than a dedicated shaper, though admittedly you give up the 1/4" collet capability.:
1/2" and 3/4" collets ($764.00 delivered).
http://www.grizzly.com/products/1-1-2-HP-Shaper/G1035
1/2", 3/4" and 1" collets ($1,410.00 delivered):
http://www.grizzly.com/products/3-HP-Shaper/G1026
Plus 1/4" spindle for the above ($72.00)
http://www.grizzly.com/products/Router-B...ndle/D3080
The Jet shaper is supposed to be more nicely finished (and more expensive) but it comes with both shaper spindles and the router collets (included) $1,150.00 + shipping.
http://www.rockler.com/jet-1-5hp-shaper-...4-spindles
No animals were injured or killed in the production of this post.
Posts: 12,606
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
03-09-2018, 02:17 PM
(This post was last modified: 03-09-2018, 02:18 PM by fredhargis.)
Throw in the cost of the shaper tooling and it comes up quite a bit versus router bits.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 127
Threads: 0
Joined: Jan 2018
DeWalt router in I think a Rockler router table top with miter bauge t-track already installed plus the fence & router mounting plate for like $140 shipped on sale. 1/2 sheet of 1/2" ply fpr a couple drawers & 1/2 sheet of 3/4" ply for the sides & bottom. 4 casters & a router table for maybe $300. Suits my needs & I'm happy to have it.
A router table can be as elaborate or simple as you need or like. No need for router lifts if that's not your thing. It's all good!!
Posts: 7,421
Threads: 1
Joined: Sep 2005
I thought I had made it clear, for the cost of a spindle, the shaper can use your 1/4 inch bits. All the shapers will linked will handle 1/2 inch bits. They are easy to hook up to dust collection, and you don’t have to mount and un-mount your router.
The pricy lifts plus a table still don’t make sense to me.
No animals were injured or killed in the production of this post.