▼
Posts: 4,006
Threads: 0
Joined: Nov 2010
After she saw this...
[attachment=12775]
Little cabinet at a store called "ODDLOTS/ BigLots. Since it is a bit smaller than what she needs, I have to expand this a bit. Width is about right, at 54"
Height? She wants it at 41" tall...this is 36"......depth is 16" over the top...can be fudged as needed. However, some things will not be used..
[attachment=12776]
3" thick top? Those metal brackets? No.
Stopped at a friends place, and picked up a stack of Ash 1 x 6 boards..
[attachment=12777]
Was just 4 planks, but the 12' lengths were a bit much. Cut them roughly in half so they would at least fit into my van. Got home, also unloaded this stack of flooring cut-offs
[attachment=12778]
These will get trimmed down a bit. Will get used for the doors...
[attachment=12779]
What looked like a drawer...is fake
 . But...I can make the entire door as a Frame & Panel item. Euro style hinges? NO, we have others to use.
The cabinet has little feet thingys...that usually break off....I can do better ones. Bottom "shelf" is about 3" thick...really? I think I can do a little better. may use 1 x 3s for a face frame? The arch detail will stay. Need to go and price & size a "Fireplace Insert" ( electric) and size the bottom opening to that.
Hopefully, I can get this done, before the first snow flake flies by
Stay tuned for part 2
Show me a picture, I'll build a project from that
▼
Posts: 4,006
Threads: 0
Joined: Nov 2010
Ok....day one. Picked out the shortest 5 planks in the stack. hauled those to the shop, took two trips, but they all "landed" on the bench
These will get cut down, edge jointed, one will get ripped.....all to make two 14" wide panels...roughly 41" long. While cutting off the worst areas...
Set four pieces aside...for the moment (before the Boss sees them)
Found my blue chalk line, snapped a couple lines..
Not about to handsaw these....bandsaw also was having issues, it was trying to follow the grain, rather than get any of the blue stuff on it's blade
After all the cutting..
Wound up with these 6 parts. the two narrow parts will get glued between two pairs of wider boards, to make a side panel.
Edges will need a LOT of work....will get out the bigger planes, and a rookie plane...stay tuned..the day wasn't quite over with, yet
Show me a picture, I'll build a project from that
Posts: 4,006
Threads: 0
Joined: Nov 2010
09-06-2018, 08:53 AM
(This post was last modified: 09-06-2018, 08:54 AM by bandit571.)
Ok, time for the jointer?
Ganged up the two narrow parts, and clamped alongside the bench.
[attachment=12785]
The Stanley No. 8 worked...IF there wasn't a bunch of high spots....then it would just hit those a bit, and stop cutting, used a jack plane to get rid of the worst areas..
[attachment=12786]
About time it got put to work, on a real job...
[attachment=12787]
And will get used as a Jack plane. Then the No. 8 could joint the entire edge. Then turn the boards to do the other edges. Decided to test fit one panel
[attachment=12788]
Back was getting a bit too stiff....decided to take a break, for a while. Marked all four of the wider boards to show what a straight edge looked like, using one of the filler strips, and a pencil.
Stay tuned, more to come...some dummy just can't stay out of the shop....
Show me a picture, I'll build a project from that
Posts: 4,006
Threads: 0
Joined: Nov 2010
Decided, later that night, to at least get one panel glued up. Since the No. 8 was a bit much for the sore back a No. 7c was dragged out....
[attachment=12789]
Clamp one 1 x6 to the side of the bench, joint one edge, test fit to the filler strip. The do one other 1 x 6. Only doing the edges that will get glue. When three parts would stack up without clamps and glue, and NO gaps showing...time to glue & clamp..
[attachment=12790]
Spread a bead of glue along one edge, moosh the next part left and right in the glue, until it sticks. Repeat for the next part. I made sure one end was lined up...less trimming to do at the top of the panel. Bottom will get a foot profile sawn into it, LATER..
[attachment=12791]
I start with a clamp in the middle, then do the ends. I add a caul on each end, to pull things flat.
[attachment=12792]
Will let this sit a day, or so....let the back rest up. maybe this evening, I can get the other side into the clamps? We'll see..
Until then, stay tuned...
Show me a picture, I'll build a project from that
▼
Posts: 6,442
Threads: 0
Joined: Feb 2006
quite a workout with that Ash compared to all that Pine you've been working lately. Can't wait to see the finished product!
Posts: 4,006
Threads: 0
Joined: Nov 2010
Trip to Menard's today...dodge showers all the way home...
Seven 1 x 2 x8'...to build the webframes I need.
Two 1 x 12 x 4'...center dividers. Pine, will be covered by face frames.....Main shelf above the $210 insert, will be a webframe, with a 1/4" plywood skin where it will show.
May wait a while, before I go to the shop. Had to use a block plane to adjust a swelled up screen door...
Sitting here in front of the A/C Unit.....trying to cool me down.
Will see how the rest of the day goes...stay tuned.
Show me a picture, I'll build a project from that
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
Good Greif Bandit. You do more by 10am then I do all day.
Love the project. How technical are you wanting to make the joints, drawers, and doors?
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 4,006
Threads: 0
Joined: Nov 2010
Have to wait and see
...usually it is the K.I.S.S. system.
Waiting on a final dimension of the insert she is buying....
Bought the 1 x 2s to build a few webframes....and a pair of Pine 1 x 12s to make the center dividers with.
Shop has been "Bug Bombed"...trying to get rid of all the pests in the shop. Gave that a day to work......maybe in the morning, I can get a little bit of work done?
Stay tuned
Show me a picture, I'll build a project from that
▼
Posts: 1,325
Threads: 0
Joined: Nov 2009
Location: Bowie, MD
George
if it ain't broke, you're not tryin'
Quando omni flunkus, moritati.
Red Green
Posts: 3,057
Threads: 0
Joined: Dec 2006
Location: Concord, NC
Bandit571 I really enjoy your builds. If you ever feel like it, please post a shop tour. I bet somebody could spend an hour or more just looking around there.
Thanks
"Life is too short for bad tools.".-- Pedder 7/22/11
|
