WTB small power feeder for router table use

[alanealane]

I'm stunned that the cheapest power feeder I can find new online is $400! 
And finding a gear reduction drive or gear motor that runs on single phase for less than $200 is very difficult based on my many hours of searching during the past week. 

Does anyone either have a little feeder they want to sell and ship? I'm really hoping to spend under $200. Hopefully that's not a pipe dream 
.

Or can anyone suggest a good source for a single phase gear reduction motor so I can make my own feeder?
A reduction ratio of 50:1 to as high as 100:1 would be ideal for my needs.

Thanks!!

[BloomingtonMike]

I'm stunned that the cheapest power feeder I can find new online is $400! 
And finding a gear reduction drive or gear motor that runs on single phase for less than $200 is very difficult based on my many hours of searching during the past week. 

Does anyone either have a little feeder they want to sell and ship? I'm really hoping to spend under $200. Hopefully that's not a pipe dream 
.

Or can anyone suggest a good source for a single phase gear reduction motor so I can make my own feeder?
A reduction ratio of 50:1 to as high as 100:1 would be ideal for my needs.

Thanks!!

Did you try surplus center for the gear motor?

[alanealane]

Did you try surplus center for the gear motor?

Yep I did but not too much caught my eye... Maybe I don't know what to look for. A lot of industrial motors are DC and require a motor control. Guess I better get on YouTube and learn some stuff so I know what to choose. I did see a nice 110V AC gear motor on eBay with a variable speed control for not too much moolah. Might give it a try. Still wouldn't mind finding one of those fancy 3 wheel units made for woodworking  

[BloomingtonMike]

[quote pid='7660719' dateline='1535413215']


alanealane
Yep I did but not too much caught my eye... Maybe I don't know what to look for. A lot of industrial motors are DC and require a motor control. Guess I better get on YouTube and learn some stuff so I know what to choose. I did see a nice 110V AC gear motor on eBay with a variable speed control for not too much moolah. Might give it a try. Still wouldn't mind finding one of those fancy 3 wheel units made for woodworking  

[/quote]

Many folks converting G0704 to cnc swap the motor out for a treadmill motor. Many times they are free. They have a speed control built in too. Maybe that could be a free or cheap source.

[alanealane]

[quote pid='7660719' dateline='1535413215']


alanealane
Yep I did but not too much caught my eye... Maybe I don't know what to look for. A lot of industrial motors are DC and require a motor control. Guess I better get on YouTube and learn some stuff so I know what to choose. I did see a nice 110V AC gear motor on eBay with a variable speed control for not too much moolah. Might give it a try. Still wouldn't mind finding one of those fancy 3 wheel units made for woodworking  

Many folks converting G0704 to cnc swap the motor out for a treadmill motor. Many times they are free. They have a speed control built in too. Maybe that could be a free or cheap source.
[/quote]

Interesting idea I'll look into that Mikie!!!!

[Stwood_]

Or can anyone suggest a good source for a single phase gear reduction motor so I can make my own feeder?
A reduction ratio of 50:1 to as high as 100:1 would be ideal for my needs.

Thanks!!

I've snagged a few off of Ebay over the years. Some are terrific buys, compared to new prices.

[alanealane]

Quick update: I found a sweet little 1/3 horsepower gear motor on eBay (still sold new for over $600 but I paid a fraction of that...although I spent a few hrs cleaning it up lol), and I purchased some pillow blocks and other stuff to make my own feeder. It will be built into the router table fence. There's a guy in Canada who posted some videos on YouTube that inspired me.

On another note I was contacted today by a longtime woodnet member who has a feeder he might be willing to part with. If I get it, it'll go on my flatmaster drum sander.

Thanks everybody!!

[Martin S.]

If you would, show us how you built the feeder, either here or upstairs somewhere.

Thanks!

[alanealane]

If you would, show us how you built the feeder, either here or upstairs somewhere.

Thanks!

I'll do my best.
Here's the videos I found inspiration from. Mine will be almost identical.
https://youtu.be/uSPyPR-hDqc shows it in action
https://youtu.be/UwodWaplsfo shows how it's made