Woodnet Forums › › Active › Woodworking Hand Tools v
How to square up Japanese chisel

▼
Aram Offline
Member
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
#8
09-29-2018, 07:53 PM
Oops. I sharpen/hone my chisels freehand on water stones. I guess I have my tendencies -- I got one of them off square by a couple degrees, which is a lot. Any suggestions for how to bring it back? I do have a LV honing guide (rarely use it, but have it) if that would help.

Thanks in advance.
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery

Web: My woodworking photo site
Find
Reply
▼
Admiral Offline
Old Tool Fool
Posts: 13,412
Threads: 4
Joined: Jun 2007
Location: New Jersey
#9
09-29-2018, 08:12 PM
(09-29-2018, 07:53 PM)Aram Wrote: Oops. I sharpen/hone my chisels freehand on water stones. I guess I have my tendencies -- I got one of them off square by a couple degrees, which is a lot. Any suggestions for how to bring it back? I do have a LV honing guide (rarely use it, but have it) if that would help.

Thanks in advance.
That would do it.  Otherwise, you could buy a Tormek....  
Laugh
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Find
Reply
▼
Aram Offline
Member
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
#10
09-29-2018, 08:42 PM
(09-29-2018, 08:12 PM)Admiral Wrote: That would do it.  Otherwise, you could buy a Tormek....  
Laugh

Sure. Do they make them hand-cranked?
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery

Web: My woodworking photo site
Find
Reply
Derek Cohen Offline
Member
Posts: 7,008
Threads: 0
Joined: Aug 2004
Location: Perth, Australia
#11
09-29-2018, 09:43 PM
Use your honing guide on 120 grit sandpaper. Trizact is long lasting. Make the run about 1m (or as long as you can).

Regards from Perth

Derek
Articles on furniture building, shop made tools and tool reviews at www.inthewoodshop.com
Website Find
Reply
knockknock Offline
Member
Posts: 106
Threads: 0
Joined: Jul 2016
Location: Poughkeepsie NY
#12
09-29-2018, 10:30 PM
Something to keep in mind, the LV honing guide is not going to magically square the edge. You will have to bias your sharping to the high side. Which comes to my suggestion, just bias your sharping each time you sharpen, eventually it will square up.
Find
Reply
▼
Aram Offline
Member
Posts: 4,814
Threads: 1
Joined: Jan 2004
Location: Eugene, OR
#13
09-30-2018, 02:23 PM
(09-29-2018, 10:30 PM)knockknock Wrote: Something to keep in mind, the LV honing guide is not going to magically square the edge. You will have to bias your sharping to the high side. Which comes to my suggestion, just bias your sharping each time you sharpen, eventually it will square up.

Thanks. Yeah, that's probably a good way to go.
Best,
Aram, always learning

"Perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away.” Antoine de Saint-Exupery

Web: My woodworking photo site
Find
Reply
Thread Modes
How to square up Japanese chisel


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.