Which router bit for flattening slabs?

[Gregory of Sherwood Forest]

I've been using a 3/4" straight bit for flattening the smaller slabs I've been doing so far, but it's time to move up in size.
I'm using a PC 2 1/4hp router. It's the largest in my current arsenal, and I'd rather not buy yet another quite yet, so this may be a limiting factor, but if I must....

So, which router bit have you folks been using to flatten your slabs, preferably in as few passes as possible and still get good results and ready for sanding?

Thanks in advance.

[FS7]

I've been using a 3/4" straight bit for flattening the smaller slabs I've been doing so far, but it's time to move up in size.
I'm using a PC 2 1/4hp router. It's the largest in my current arsenal, and I'd rather not buy yet another quite yet, so this may be a limiting factor, but if I must....

So, which router bit have you folks been using to flatten your slabs, preferably in as few passes as possible and still get good results and ready for sanding?

Thanks in advance.

I use the MLCS bit and accept that I will have to sand when I'm done. I'd sand anyway and the time savings is worth it.

Google bottom cleaning bits. I use a 2" bit, as anything bigger really requires a 3+ HP router (which I don't have). 2" is still pretty large and right at the edge of what I'm comfortable with in a non-table router.

[Huxleywood]

I've been using a 3/4" straight bit for flattening the smaller slabs I've been doing so far, but it's time to move up in size.
I'm using a PC 2 1/4hp router. It's the largest in my current arsenal, and I'd rather not buy yet another quite yet, so this may be a limiting factor, but if I must....

So, which router bit have you folks been using to flatten your slabs, preferably in as few passes as possible and still get good results and ready for sanding?

Thanks in advance.

The current thinking seems to lean toward using insert spoil board bits like Amana makes.

[Rob Young]

I've been using a 3/4" straight bit for flattening the smaller slabs I've been doing so far, but it's time to move up in size.
I'm using a PC 2 1/4hp router. It's the largest in my current arsenal, and I'd rather not buy yet another quite yet, so this may be a limiting factor, but if I must....

So, which router bit have you folks been using to flatten your slabs, preferably in as few passes as possible and still get good results and ready for sanding?

Thanks in advance.

I have one of these, or maybe just a bit smaller :

Scary bit

I think I used it once as a way for flattening some boards and it was quite the operation.  If I can find it, do you want to try it?

[Gregory of Sherwood Forest]

Thanks Huxleywood, that's the bit I was thinking of, but couldn't recall the name. I think I'll be investing in one. I can use the $$ I saved on that $207 DW735 shelix cutter deal!

Thanks Rob, but I'll pass on that. If you weren't confident using it, I probably wouldn't be either.

[Rob Young]

Thanks Huxleywood, that's the bit I was thinking of, but couldn't recall the name. I think I'll be investing in one. I can use the $$ I saved on that $207 DW735 shelix cutter deal!

Thanks Rob, but I'll pass on that. If you weren't confident using it, I probably wouldn't be either.

Oh, it worked, but because it is 2-1/2" across, I had to turn down speed and take shallow cuts.  Probably could have done it just as quickly with a 3/4" and a deeper cut.

More a test of the clamping method for the small piece than anything else.

[EdL]

I've used an 1 1/4 diameter mortice bit for my workbench top, worked great.

Good thing, it was all I had......

Ed

[Stwood_]

I've used an 1 1/4 diameter mortice bit for my workbench top, worked great.

Good thing, it was all I had......

Ed

Ayup. Mine is whiteside brand, used for flushing face frames to ply box sides.
I bought a lipping base from Pat Warner for router use and he recommended the bit.

[Big Dave]

Both Infinity & Whiteside make a bit for flattening slabs. I read a review of these not too long ago that had both of them doing quite well, but I've never used either one...

Two pennies worth...

Dave

[fishhh4]

Saw this , in this .