Posts: 38,525
Threads: 0
Joined: Feb 2002
Location: East Texas
Reality is that which, when you stop believing in it, doesn't go away. - Philip K. Dick
Mark
Posts: 25
Threads: 0
Joined: Feb 2018
I have a large collection of drill bits (many hand-me-downs from my dad when he passed away) but of varying degrees of sharpness. I presently have my eye on obtaining a Drill Doctor and sharpening instead of replacing drill bits. It seems like it would be more cost effective in the long run, particularly at the price of mid-level quality drill bits - which will still become dull and need replaced (or resharpened).
My understanding of titanium (or similar) drill bits is that one function is to help dissipate heat which is a major killer of drill bits and likewise their sharpness.
Posts: 4,444
Threads: 0
Joined: Jan 2005
(12-27-2019, 10:42 PM)Bibliophile 13 Wrote: What’s your favorite affordable or mid-grade twist bits for general wood drilling?
I’ve not been impressed with the titanium coated ones I’ve been using lately. They get dull way too quickly. I’m hoping to get some that will hold up to more than 20-30 holes before going dull.
Usually brad point and forstner bits are used for woodworking. Twist drills also called machine drills are used for metal . I like many others have used twist drills for wood because of many sizes available. To answer your question , Harbor Freight sometimes has a 29 piece set for as low as $10.00. I have 3 sets, one set is modified for brass. I am very happy with the quality . You should be able to bore 100+ holes in wood with any twist drill, coated or not. Is it possible the drill bit is over heating? These bits are made to drill at a fast speed but may overheat if forced in a deep hole. Cleveland Tap and Drill makes better quality drills but for wood I doubt that you will see a difference.
mike
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
I have a few sets of the titanium 29 piece twist bits from HF (10 bucks or less) and I've had good luck with them in mild steel. I have old HSS bits and all types of steels bits are made from. For tougher steels like 4140 or stainless, I use the cobalt set- no complaints here.
I don't know how yours are dulling in wood unless they are getting too hot because your not pecking the bit (Pulling it out while drilling to clear it from getting clogged), or you're drilling too slow and rubbing instead of cutting. But then I suspect the wood would be smoking up the shop.
Regular 118* or 135* twist bits aren't the best bits on wood. They tear the wood out easily, but with high speeds do ok.
Brad point bits are much better. Stay away from cheap ones. A good 20+ set might cost 60-80 bucks.
Posts: 2,581
Threads: 0
Joined: Apr 2012
For drilling smaller holes in wood I don't think you can beat the Lee Valley lipped brad points -
https://www.leevalley.com/en-us/shop/too...int-drills
They aren't the cheapest, but cut cleanly and stay sharp.
Phil
Posts: 12,605
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
I never know what "affordable" means in these threads, since that's such a moving target. But I've used a set of the LV lipped bits linked by Phil for quite a few years, and they still cut the cleanest, fastest, holes of any of my bits. The set of 7 has been enough to do anything I need.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 10,717
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
Another vote for the Lee Valley set. Buy the smaller set and add bits as the need and budget exists. Compared to general twist bits, you will be amazed at the clean holds a good brad point bit will give you. And the point on the brad point bit helps to more accurately locate the bit before drilling.
Still Learning,
Allan Hill
