Posts: 832
Threads: 0
Joined: Apr 2009
Location: Pacifc North Wet --AKA WA
Magnetic tip help retain the little "oops" screws??
Posts: 220
Threads: 0
Joined: Feb 2006
Location: S. E. Alabama, formally from Wisconsin.
Use a paint stick and mark the dull side, for future reference.
S.E. Alabama, formerly from Wisconsin.
Posts: 18,497
Threads: 0
Joined: Jul 2006
Location: Milwaukee area
I'm no expert but I've read of problems getting them repeated level because sawdust in and around them gets under them when loosened.
So I'd hit it with an air gun and make sure there is no sawdust hiding anywhere.
Don't accidentally hit an insert with the gun.
Posts: 892
Threads: 0
Joined: Apr 2006
Location: Trout Creek, Montana
09-23-2020, 10:25 PM
(This post was last modified: 09-23-2020, 10:34 PM by lift mechanic.)
I have never turned all the cutters, only when chipped. First thing I have done is put a small drop of penetrating oil, I like Kroil. on the edge of the screw head. Then remove the screw. Clean the "seat" where the insert seats"CLEAN". Get every bit of wood out of the seat. Clean the screw. Clean the bottom of the insert. Install the screw and insert into the threaded hole. Finger tighten the screw. Wiggle the insert while starting to tighten it down, this is to seat the cutter. Then tighten to torque specs. On my Byrd head it called for 45 in/lbs on a #25 Torx head screw.
Treat others as you want to be treated.
“You only live once, but if you do it right, once is enough.” — Mae West.
24- year cancer survivor
Posts: 10,776
Threads: 0
Joined: Jul 2005
Location: Front seat on the Struggle Bus
What is the reason for rotating the cutters and how many bd/ft has been thru it?
Ed
Posts: 887
Threads: 0
Joined: Sep 2009
Location: Carlisle, PA
Make sure you're using the correct Torx bit/driver. I bought a 15" Powermatic a few months back and the first thing I did was remove all the cutters to facilitate cleaning off all the protectant goo. The specs for the Powermatic call for a Torx 25 PLUS. I also picked up
THIS torque wrench from Home Depot and it worked perfectly. It was time consuming, but I put on the satellite radio, pulled up a stool and just followed the directions ensuring the mating surfaces was clean with a drop of oil on the screw threads and aligning it by hand while tightening it down.
Posts: 24,331
Threads: 0
Joined: Feb 2002
Location: Elizabethtown, KY
No idea how many BF -- it's been several years -- but there are several ridges showing up from unfriendly objects in the boards I've planed. Two or three cutters are missing entirely from such impacts. Too much of the lumber I plane is "old stock" that was sawn years ago and lots of dirt, etc from storage.
Knew I wanted to mark them but didn't think of a Paint Stick. .
Sounds like air compressor will get a workout
Thanks for the help.
"Truth is a highway leading to freedom" --Kris Kristofferson
Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
Posts: 1,618
Threads: 0
Joined: Feb 2010
Location: Coast of Maine
Buff the back side of the inserts on 600 grit paper to remove any burrs or accumulated crud. I use PSA paper on a surface plate, MDF will work too. One finger on the insert, a few quick swipes. You can "feel" when it is clean.
g
I've only had one...in dog beers.
"You can see the stars and still not see the light"
The Eagles: Already Gone
