#16
I'm building a live edge dining table using air dried walnut slabs for the top, and cherry for the legs.

I'm looking for a matte finish, preferably wipe on, that will provide durability for use as a dining table. It will get mostly occasional use, nit every day, but I want it to be moisture resistant for things like spills.

All advice is welcome.

Thanks
Jason
Mesurei, cutti, cursi

Reply

#17
Any wiping varnish should meet your needs.  I like Arm-R-Seal satin but you could use Waterlox OSF for a darker hue and rub it out after it's cured for a month.  

John
Reply

#18
(02-05-2021, 01:12 PM)jteneyck Wrote: Any wiping varnish should meet your needs.  I like Arm-R-Seal satin but you could use Waterlox OSF for a darker hue and rub it out after it's cured for a month.  

John

this.  john nailed it.  ARM on walnut is my go-to, but waterlox is also beautiful.  one's a urethane resin, one's an alkyd resin.  the waterlox is deeper color, more orange.  on my walnut pieces in my house, i use arm-r-seal over seal-a-cell.

good luck, post pictures when you're done!  sounds like one heck of a piece.
Reply

#19
(02-09-2021, 08:00 PM)zaret Wrote: this.  john nailed it.  ARM on walnut is my go-to, but waterlox is also beautiful.  one's a urethane resin, one's an alkyd resin.  the waterlox is deeper color, more orange.  on my walnut pieces in my house, i use arm-r-seal over seal-a-cell.

good luck, post pictures when you're done!  sounds like one heck of a piece.

Not that it matters much, but Waterlox uses a phenolic resin.  P&L 38 (I think that's the name) uses an alkyd resin.  And you are right that Waterlox gives a deeper color.  Arm-R-Seal is actually pretty clear for an oil based varnish.  I've used it on curly maple and it imparts very little amber hue.  

John
Reply

#20
(02-10-2021, 10:20 AM)jteneyck Wrote: Not that it matters much, but Waterlox uses a phenolic resin.  P&L 38 (I think that's the name) uses an alkyd resin.  And you are right that Waterlox gives a deeper color.  Arm-R-Seal is actually pretty clear for an oil based varnish.  I've used it on curly maple and it imparts very little amber hue.  

John

John - thanks for this, of course, you are correct.  arm-r-seal is wonderful stuff... in fact, i used some just this morning on three walnut mantles. 

by the way - my go-to now for hard maple is odie's oil.  i'm yet to find a more beautiful finish on maple.  pretty on walnut, too.  and, zero VOCs, which is nice.
Reply

#21
(02-10-2021, 01:50 PM)zaret Wrote: John - thanks for this, of course, you are correct.  arm-r-seal is wonderful stuff... in fact, i used some just this morning on three walnut mantles. 

by the way - my go-to now for hard maple is odie's oil.  i'm yet to find a more beautiful finish on maple.  pretty on walnut, too.  and, zero VOCs, which is nice.

Thanks.  I've wanted to try Odie's Oil.  Might just have to now.  

John
Reply
#22
I hope that baby stays flat!!

Are you installing any metal braces?
Reply

#23
(02-10-2021, 10:36 AM)rwe2156 Wrote: I hope that baby stays flat!!

Are you installing any metal braces?

No. That woods been in the shop for ~3 years and off the mill for at least 6. It hasn't moved, and it is made op of 4 different boards, and the grain direction alternates. None of my live edge pieces have moved at all.
Jason
Mesurei, cutti, cursi

Reply
Finish advice for live edge walnut dining table


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.