Woodnet Forums › › Active › Woodworking v
Kennedy Tool Box Hinge

▼
BrentDH Offline
Member
Posts: 318
Threads: 0
Joined: Nov 2011
Location: Rochester, MN
#9
03-13-2021, 06:31 PM (This post was last modified: 03-13-2021, 06:33 PM by BrentDH.)
I have an older Kennedy tool box that sits on a Kennedy chest.  I would like to move it to a new spot in my shop, but to put it where I want I have to remove the lid for height clearance.  I don't really mind taking the lid off which leaves it unlocked all the time, but I cannot figure out how to remove it.  I thought maybe the hinge pin was just mushroomed a bit on each end.  So I very carefully ground one end off to the point where I am sure there is no mushroom.  Then I tried to tap it out with a pin.  No luck.  Doesn't budge.  I don't really want to destroy anything here, and would like to be able to put it back together some day.  I am sure they intentionally made this difficult to do or else the locking mechanism could be easily compromised.  Does anyone know how they attached the hinge pin or how to get it out?  Thanks in advance.

Edit. One option would be to just not use the very top compartment and leave the lid closed all of the time, but that locks all the drawers.
Find
Reply
▼
Bob10 Offline
Sir Member
Posts: 40,096
Threads: 0
Joined: Apr 2007
#10
03-14-2021, 12:21 AM
(03-13-2021, 06:31 PM)BrentDH Wrote: I have an older Kennedy tool box that sits on a Kennedy chest.  I would like to move it to a new spot in my shop, but to put it where I want I have to remove the lid for height clearance.  I don't really mind taking the lid off which leaves it unlocked all the time, but I cannot figure out how to remove it.  I thought maybe the hinge pin was just mushroomed a bit on each end.  So I very carefully ground one end off to the point where I am sure there is no mushroom.  Then I tried to tap it out with a pin.  No luck.  Doesn't budge.  I don't really want to destroy anything here, and would like to be able to put it back together some day.  I am sure they intentionally made this difficult to do or else the locking mechanism could be easily compromised.  Does anyone know how they attached the hinge pin or how to get it out?  Thanks in advance.

Edit.  One option would be to just not use the very top compartment and leave the lid closed all of the time, but that locks all the drawers.

I would bet you can find your answer here 

https://www.garagejournal.com/forum/
Phydeaux said "Loving your enemy and doing good for those that hurt you does not preclude killing them if they make that necessary."


Phil Thien

women have trouble understanding Trump's MAGA theme because they had so little involvement in making America great the first time around.

Find
Reply
Stwood_ Offline
Member
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
#11
03-14-2021, 04:56 PM
Unhook the strap that runs down for the drawer locks maybe......
Steve

Mo.


I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Find
Reply
AHill Offline
Honored Veteran
Posts: 10,718
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
#12
03-14-2021, 07:32 PM (This post was last modified: 03-14-2021, 07:46 PM by AHill.)
Maybe this might help:

https://buykennedy.com/product-category/...ent-parts/
https://www.instructables.com/Repair-a-U...ist-Chest/
Still Learning,

Allan Hill
Find
Reply
Thread Modes
Kennedy Tool Box Hinge


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.