▼
Posts: 16,471
Threads: 0
Joined: Mar 2005
I activated the dado brake today, and my hands were nowhere near the blade. I was using the Incra box joint jig and after several cuts, bamm! There was no indication that the blade touched the jig, but the set up calls for close tolerances. Something must have wiggled. ![[Image: yellowyes.gif]](https://www.forums.woodnet.net/images/graemlins/yellowyes.gif)
In the future, when I get a new brake, I think I'll use the little key to turn the sensor off. When using the jig there is no reason to have hands near the blade. Live and learn.
---
See ya later,
Bill
▼
Posts: 8,381
Threads: 1
Joined: Mar 2000
(05-23-2021, 10:06 PM)Bill_de Wrote: I activated the dado brake today, and my hands were nowhere near the blade. I was using the Incra box joint jig and after several cuts, bamm! There was no indication that the blade touched the jig, but the set up calls for close tolerances. Something must have wiggled.
In the future, when I get a new brake, I think I'll use the little key to turn the sensor off. When using the jig there is no reason to have hands near the blade. Live and learn.
---
I seem to recall a discussion not too long ago about this jig and those close tolerances when used on the SS. How close is a metal portion of the jig to the spinning blade?
▼
Posts: 16,471
Threads: 0
Joined: Mar 2005
(05-24-2021, 07:49 AM)WxMan Wrote: I seem to recall a discussion not too long ago about this jig and those close tolerances when used on the SS. How close is a metal portion of the jig to the spinning blade?
You start the calibration with the jig just touching the blade. As you adjust, the part of the jig moves away from the blade. I'm not sure what happened, because I made a few cuts before the brake activated. I'll be taking a closer look as I wait for the new brake to come.
---
See ya later,
Bill
Posts: 12,602
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
05-24-2021, 01:03 PM
(This post was last modified: 05-24-2021, 01:04 PM by fredhargis.)
How's the dado set (or box joint set)...much damage?
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
▼
Posts: 16,471
Threads: 0
Joined: Mar 2005
(05-24-2021, 01:03 PM)fredhargis Wrote: How's the dado set (or box joint set)...much damage?
The box joint set appears to be fine. The brake has been shipped and should be here in a day or two.
I think it was a message from the gods that I should be spending more time outdoors while the weather is nice.
See ya later,
Bill
Posts: 30,415
Threads: 1
Joined: Dec 2002
Location: DuPage County, Illinois, USA
So you now need a new dado set plus a new trigger module, right?
▼
Posts: 16,471
Threads: 0
Joined: Mar 2005
(05-24-2021, 02:44 PM)Cian Wrote: So you now need a new dado set plus a new trigger module, right?
Hopefully just the brake module. I'll know for sure when it's up and running.
--
See ya later,
Bill
Posts: 1,617
Threads: 0
Joined: Feb 2010
Location: Coast of Maine
05-24-2021, 04:03 PM
(This post was last modified: 05-24-2021, 04:04 PM by shoottmx.)
(05-24-2021, 02:44 PM)Cian Wrote: So you now need a new dado set plus a new trigger module, right?
About 6-7 years ago I fired the cartridge on my SS Freud dado with aluminum fence contact. I checked the teeth with a loupe, saw no issues. Laid the outer blades on a surface plate, both were flat--no rocking. Been using it ever since with no issue.
g
I've only had one...in dog beers.
"You can see the stars and still not see the light"
The Eagles: Already Gone
Posts: 4,133
Threads: 0
Joined: Oct 2009
Location: Lawrence, KS
(05-23-2021, 10:06 PM)Bill_de Wrote: I activated the dado brake today, and my hands were nowhere near the blade. I was using the Incra box joint jig and after several cuts, bamm! There was no indication that the blade touched the jig, but the set up calls for close tolerances. Something must have wiggled.
In the future, when I get a new brake, I think I'll use the little key to turn the sensor off. When using the jig there is no reason to have hands near the blade. Live and learn.
---
Keep in mind that the override feature re-sets every time the big red paddle is cycled. Probably won't be cycling the power during a box joint session but something to remember if you use it for other purposes.
Don't sweat the petty things and don't pet the sweaty things. -- G. Carlin
Posts: 244
Threads: 0
Joined: Oct 2011
You should have the blade inspected by a sharpening service. There could be a fracture that may cause a tooth to fly off in use.
|
