▼
Posts: 116,182
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
05-23-2024, 09:29 AM
So as not to hijack other threads, I decided to post this link...I think most people are shaving hair on their arms or slicing printer paper to demonstrate how sharp they can get their edges. But is that really good enough? How clean is the cut? IOW, how sharp is "sharp"..Most of he time I stab a paper towel then make a slicing cut downward...when it cuts CLEANLY, {smooth edges, no tearing} it's good enough for woodcarving or woodworking. And if you really want to get serious, try the same thing using single ply, DRY toilet tissue..and dampened tissue takes it to an even higher plane. I haven't gotten there yet! Make your towel cut in TWO directions because kitchen towels seem to be woven in two directions, like cloth.
If you think woodworkers are obsessed with sharpening, check out some of the shaving forums!!
https://www.sharpeningsupplies.com/blogs...bPEALw_wcB
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
▼
Posts: 4,021
Threads: 0
Joined: Nov 2010
One of two ways..
Either there is a spot on my arm that no longer has any hair..
or..
I notice drops of blood on a project, but did not feel a thing..and it heals without a scar..
As long as the edge does the tasks I ask of it...I just get back to work..
Show me a picture, I'll build a project from that
▼
Posts: 116,182
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(05-23-2024, 11:30 AM)bandit571 Wrote: One of two ways..
Either there is a spot on my arm that no longer has any hair..
or..
I notice drops of blood on a project, but did not feel a thing..and it heals without a scar..
As long as the edge does the tasks I ask of it...I just get back to work.. ..................
The older you get, the easier you bleed!!!!! Don't ask how I know...
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 2,201
Threads: 0
Joined: Dec 2006
Now there’s a dilemma…do you use sharp woodworking tools, or do you use dull ones ‘cause chicks dig scars?
Posts: 1,396
Threads: 0
Joined: Aug 2008
05-23-2024, 04:33 PM
(This post was last modified: 05-23-2024, 04:33 PM by ZachDillinger.)
I usually try to put the blade/chisel/whatever into my thumbnail and pare a little slice. If it sticks in immediately it is sharp, if it sort of skates a little on the nail then it isn't sharp enough. On plane irons I go a step further and try to pare end grain white pine. If it cuts that cleanly then I'm in business.
Zachary Dillinger
https://www.amazon.com/author/zdillinger
Author of "On Woodworking: Notes from a Lifetime at the Bench" and "With Saw, Plane and Chisel: Making Historic American Furniture With Hand Tools",
Posts: 7,011
Threads: 0
Joined: Aug 2004
Location: Perth, Australia
05-23-2024, 06:59 PM
(This post was last modified: 05-23-2024, 06:59 PM by Derek Cohen.)
If the plane or chisel is not cutting easily, I stop and sharpen. After sharpening I do not test the edge ... well perhaps very occasionally out of curiosity ... just trust your sharpening method is reliable. This will be tested as soon as the tool is once again in use.
Regards from Perth
Derek
Posts: 3,955
Threads: 0
Joined: Feb 2005
I usually test on newspaper doing the S pattern as I slice down. That usually means it plenty sharp for my purposes.
▼
Posts: 116,182
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(05-23-2024, 07:22 PM)Ricky Wrote: I usually test on newspaper doing the S pattern as I slice down. That usually means it plenty sharp for my purposes. .....................
On the woodcarving knives I make, I look for the shiny surface imparted on end grain wood by the edge of a really sharp blade..It appears to have been waxed. After about 15 minutes of carving, I take he blade to the small buffer I keep handy to touch up the keen edge even a properly hardened blade will lose. But actually, I have been sharpening so many years that I just know when I have a blade sharp enough to suit me. Really sharp edges are a joy.
It is surprising to me how many carvers do not know how to sharpen their tools. I saw one carver at a show with a cigar box full of carving knives, pay a fellow with a Viel belt grinder $3.00 to sharpen each one. Most just needed to be power stropped.. He didn't know how to sharpen, but he had some fine carvings on his display table!!
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 216
Threads: 0
Joined: Jan 2018
05-24-2024, 03:30 AM
(This post was last modified: 05-24-2024, 04:35 AM by CStan.)
When your edges can produce this, they're sharp enough:
https://www.youtube.com/watch?v=5Bhu7HjIGAk
Roughly 270 years ago...
▼
Posts: 7,011
Threads: 0
Joined: Aug 2004
Location: Perth, Australia
05-24-2024, 07:31 AM
(This post was last modified: 05-24-2024, 07:32 AM by Derek Cohen.)
(05-24-2024, 03:30 AM)CStan Wrote: When your edges can produce this, they're sharp enough:
https://www.youtube.com/watch?v=5Bhu7HjIGAk
Roughly 270 years ago...
Sometimes I whittle a quick Rococo chair back to test an edge. Nothing excessive.
Regards from Perth
Derek
|