Prepping for a new start

[Derek Cohen]

With the chairs done, next on the agenda is an 8-seater dining table. One of the pleasures in being an amateur is that I get to enjoy the time between builds as much as the builds themselves. My question for all is "what do you do between builds, or in preparation for a new build?".

The table top is to be 68-70" long, 40" wide, and 1 1/4" thick (there will be a 1/4" bevel), in Rock Maple. The Rock Maple is to link with the chairs I built. The legs will be 3" cylinders in Jarrah, 30" high, with 3" Jarrah stretchers connecting. Think of this as a contemporary version of the existing 6-seater 250 year-old table we are replacing (which has 5" stretchers and 2 1/2" diameter legs) ...



But this post is not about design. That is for another time. This post is about prepping.

The Jarrah legs come in 3 1/2" posts, in around 80" lengths. They were cut down roughly, at this stage, with a chainsaw ...



There are 4 wide 10' long and 2" thick Rock Maple boards here. They will be cut down and re-sawn when ready to be used.



I spent most of the past weekend cleaning the workshop. It was covered in dust from the grinding, sanding, scraping, rasping and shaving that dominated my time over the past few months. The jointer-thickness/planer was cleaned, as was the slider, while the bandsaw was stripped, cleaned and a carbide Lenox Woodmaster CT 1" blade set up for resawing. All this wood is damned hard stuff. The dust extractor bins were emptied, and the ceiling filter cleaned.

There is some pleasure in making all good again, especially with a good coffee to sip, and great jazz to listen to on the workshop stereo.

While the machines are important, attention was given to the hand planes I will use. Especially the Veritas #7 Custom Jointer - as good as my Hammer A3-31 jointer is, all edges are finished with a hand plane for invisible joins.

Stripping down the #7, it was clear that it needed a good cleaning.



It's amazing to find this much cr@p under the frog ...



That warranted refreshing the underside of the chipbreaker. You can make out the silver line behind its leading edge ...



The blade was sharpened (30 degrees) and set up with the chipbreaker closed down - the last thing one wants when planing edges is any tearout ...



The chipbreaker received a clean microbevel of 75 degrees. The wooden angle behing provides a guide for freehanding this ...



Re-assembled and looking like new! Incidentally, the frog angle here is 40 degrees (that is about as low as one can go), hence how important it is to set the chipbreaker carefully as it would otherwise be a recipe for disaster.



Testing on a narrow board ...



The even, thin shavings let me know that it is good to go ...



I also took the time to make a side fence for the #7. I've never used one before on this plane, and was curious to find out how accurate (square) it could plane (it leaves a perfect edge). The metal bits come from a Veritas Skew Rabbet Plane ...



And then this was rinse and repeat for a #4 Veritas Custom Smoother ...



.. and a LN #3 ...



That was fun ...



Regards from Perth

Derek

[bandit571]

About the same in my shop...Tool Maintenance...and put away any tools I am done with....refresh chisel edges...

Currently working through a Wood Joint Class...like the one I took as a Freshman in High School (dating meself here) in the Fall of 1968...We had to getting graded on each joint, done with hand tools only, and get a Passing Grade...BEFORE we were allowed anywhere near the IND ARTS Shop's Rockwell/Delta power tools...

We also learned how to adjust and USE a MitreBox & Saw...

hard part?   Remembering back that far in time...

Am up to "Worksheet No. 4" this week...
[attachment=51656]
Your's are looking good!

[Derek Cohen]

Thanks Steven!

Which specific tools would you set aside and what tune up preparation do you do for each of those joints?

Regards from Perth

Derek

[Bill Holt]

My question for all is "what do you do between builds, or in preparation for a new build?".

Regards from Perth

Derek

After a "big" build, I will sharpen the edge tools and clear out excess cut offs.  Between builds, I relax by turning bowls.

[bandit571]

A selection of tools..

   
Chisels and a Marking knife...were all sharpened at the start..

   
A selection of both rip and cross cut saws were on the bench...Squares were checked before use...

   
The Veritas cutter was checked to see IF it needed a refresh..

   
Found that even an old Jackson Backsaw can work a bit better, IF I rub an old Candle just above the tooth line...smooths things out..

Planes that got a bit too much use on the last two projects, were worked over, and are ready for the next Projects...