Posts: 36,538
Threads: 3
Joined: Nov 2004
Location: RTP, NC
I looked at it some more this morning and near as I can tell the plastic mount is bolted through the escutcheon and the tile with 2 bolts, and there are another 2 that I assume are bolted through the tile under the escutcheon. It doesn't seem to be glued to the tile.
Posts: 27,910
Threads: 0
Joined: Jul 2002
Location: Pacific ocean now much further away!
I’ve replaced four of those in the last two years, not just the cartridge but the entire thing. I was retiling all the showers, so I thought I’d replace the valves at that time.
The valve body should be attached to blocking.
Without pics, I can only guess what you need, maybe try replacing the cartridge first to see if it fixes the problem?
VH07V
Posts: 2,723
Threads: 0
Joined: Dec 2005
Is it possible that a faulty cartridge could be the source of your leak? Might it be worthwhile before tearing things apart to replace cartridge: a 30 minute job?
Posts: 27,910
Threads: 0
Joined: Jul 2002
Location: Pacific ocean now much further away!
I assume this is copper piping. If you’re comfortable with soldering, just replace the valve, that way you know it’s done. The tricky part is the tub spout part. That may require some careful measuring depending on which manufacturer you pick.
I couldn’t get the pic to load, sorry.
VH07V
Posts: 246
Threads: 0
Joined: Sep 2004
08-05-2024, 11:27 PM
(This post was last modified: 08-05-2024, 11:30 PM by kencombs.)
(08-01-2024, 08:24 PM)crokett™ Wrote: The valve in our shower is leaking. I opened the wall to start getting things dried out. I need to replace the valve; it has a slow drip even when turned off. The shower is tiled. From the back I can see a metal valve body mounted to a round plastic mount. The mount is mounted against the back of the tile and the back of the plastic mount is flush with the back of the backer board - there's a hole in the backerboard for the plastic mount. There is no framing or anything holding the valve in place. There are 4 bolt ends sticking out of the valve body. I've installed 2 shower valves (none in several years) and both of them were installed mounted to framing. Is this one screwed through the tile under the escutcheon? I am hoping it is not some kind of adhesive as I don't want to be messing with the tile.
What does it look like from the front with the trim removed? I'm betting the builder used the tile and thinset to lock the plastic mount in place, or maybe it has a flange seated between the tile and backer board. \
It may, maybe, be possible to find a valve that will fit into the same mount. Do you know the brand?
At least the piping is easy. Just be sure to grab a crimp ring cutter so you can reuse the pex. I'd opt for the clamping style replacements instead of crimp
Posts: 36,538
Threads: 3
Joined: Nov 2004
Location: RTP, NC
The brand is some off-brand wholesale one. I'd have to look it up again. The supplier doesn't have parts. I already know that. I'm not going to try to find a compatible valve set. My wife wants a black one anyway. Not sure what it looks like with the trim ring off yet. I will find out this weekend. I don't think there's a flange on the plastic part. I can't see one from the back. If there is, it's getting cut off to remove the old valve and mount. My assumption right now is the bolts that run through the plastic mount are screwed through the tile. I am not afraid to replace the valve, done that before but it's been 10 or so years. It was unexpected to not see any framing for the existing valve. I've demoed a few bathrooms over the years and replaced a couple shower/bath valves never seen one that didn't have the valve mounted to some kind of framing. This is shower only, no tub spout to worry about.
Since I plan on leaving some sort of permanent access anyway, I will get some shutoff valves like sinks have and install those. That way I can turn the water back on and will be under less time pressure.
