Posts: 2,065
Threads: 1
Joined: Feb 2009
Location: Mechanicsville, Md
I don't know of a way. I had a leaky roof in my shop and my saw ended up with a couple of rust stains. I grabbed my RO sander and proceeded to start with a little coarser grit paper and progressed through the finer grits. Followed up with some good wax. The stains are still there but it is clean and smooth. Adds character.
I no longer build museums but don't want to change my name. My new job is a lot less stressful. Life is much better.
Garry
Posts: 1,981
Threads: 1
Joined: Aug 2016
(09-13-2024, 11:17 AM)blanning Wrote: I recently bought a lathe from grizzly. So far I love it. But it has one minor problem. The way it's shipped, the cast iron legs are stored on top of the bed in the crate. This has caused a stain on the bed. It's smooth as glass. So it's just a discoloration. I tried some rust stain remover that came with the Boeshield. And it helped slightly. But nowhere near enough.
Is there a good way to clean these kinds of stains off of cast iron?
Ask Grizzly. Roly
Posts: 1,682
Threads: 0
Joined: Apr 2005
09-14-2024, 04:07 PM
(This post was last modified: 09-14-2024, 04:08 PM by kurt18947.)
(09-13-2024, 11:17 AM)blanning Wrote: I recently bought a lathe from grizzly. So far I love it. But it has one minor problem. The way it's shipped, the cast iron legs are stored on top of the bed in the crate. This has caused a stain on the bed. It's smooth as glass. So it's just a discoloration. I tried some rust stain remover that came with the Boeshield. And it helped slightly. But nowhere near enough.
Is there a good way to clean these kinds of stains off of cast iron?
I don't really think there is or at least I haven't found it. I have a Grizzly table saw that had some rust spots and I was able to get the rust spots off with WD40 and and gray abrasive pad. It's as smooth as I could ask but I can still see the discoloration. As museumguy says, it's character.
Posts: 10,720
Threads: 0
Joined: Jul 2005
Location: Front seat on the Struggle Bus
My Uniasw has a few from its previous life....yup, character.
Ed
Posts: 312
Threads: 0
Joined: Nov 2011
Location: Rochester, MN
09-14-2024, 05:59 PM
(This post was last modified: 09-14-2024, 06:00 PM by BrentDH.)
I saw this from the Wood Whisperer the other day. Not sure if it helps. I am watching this discussion closely since I bought a new Sawstop a while back and it seems like every time I touch the surface it leaves a blemish.
https://youtu.be/pTCILcFjjio?si=Olh4CB2hB4LPyRNe
Posts: 312
Threads: 0
Joined: Nov 2011
Location: Rochester, MN
Blanning, if you try it I would be interested to hear about your results and impressions.
FYI. There was a comment under the YouTube video about it destroying the hook and loop pad on somebody’s festoon sander and they weren’t very happy about that. So maybe do some checking on how to protect your sander pad.
Posts: 12,561
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
(09-15-2024, 10:04 AM)mad_planter Wrote: If you press down to hard you'll generate enough heat to mess up the velcro.
^^^^^^^that's the reason a lot of folks have to replace their pad so often.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
