#20
Question 
I have a brass faced union that I cannot get to seal. Tightened to the point that I fear something will break. [Standing on one pipe wrench with a pipe on the handle of the other wrench]. Should I try some pipe dope on the brass faces?

My boss is a Jewish carpenter. Our DADDY owns the business.
Trying to understand some people is like trying to pick up the clean end of a turd.
Reply

#21
I don't mean to be a smart butt but did you check if something got caught up in between?  piece of hard water build up or something between the loose nut and piece under it
Phydeaux said "Loving your enemy and doing good for those that hurt you does not preclude killing them if they make that necessary."


Phil Thien

women have trouble understanding Trump's MAGA theme because they had so little involvement in making America great the first time around.

Reply
#22
I would give it a try, nothing to loose.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. RMB
The SO asked me today, "what are you going to do to day"? I said "nothing".  She said, "that's what you did yesterday"! Me, "Yes love, but I was not finished yet"!!!!!!!!
Smirk

Reply
#23
Brass faced? Solid brass, galvanized steel or black? Solid brass would be the best choice. As Bobski mentioned, make sure the sealing faces are clean and not scored or pitted. They can be cleaned with fine grit cloth or scotchbrite. A bit of dope on the nut threads will make it easier to tighten and later remove.
Reply

#24
Galvanized steel with brass faces. Faces are clean. Pipe dope on the threads and the non-threaded half where the nut comes against it.

My boss is a Jewish carpenter. Our DADDY owns the business.
Trying to understand some people is like trying to pick up the clean end of a turd.
Reply
#25
Is it a new union?  Are the threads clean all the way?

I'd take it apart and see if the "nut" would go all the way to make sure there's nothing in the threads to stop it short of full tight.
"Truth is a highway leading to freedom"  --Kris Kristofferson

Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
Reply

#26
The pipe needs to be aligned, a few degrees of deflection can cause leaks, as can a mismatched union ( you shouldn't swap parts ).  A thin rubber gasket can be fitted but if this is part of the electrical ground, put a jumper around the union.
Blackhat

Bad experiences come from poor decisions. So do good stories. 


Reply

#27
The pipe dope could very well be your problem. A little errant dope on the mating surfaces could keep it from sealing. The same issue occurs with flare fittings on soft copper when folks feel compelled to apply pipe dope where it isn't needed.

Rick
Reply

#28
(11-12-2016, 09:57 PM)therick34 Wrote: The pipe dope could very well be your problem. A little errant dope on the mating surfaces could keep it from sealing. The same issue occurs with flare fittings on soft copper when folks feel compelled to apply pipe dope where it isn't needed.

Rick

I dont that was in the original post, it was a suggestion for a better seal.
Heck my plumbers put it on the rubber ring between the toilet tank and toilet bowl, on all sides.
,
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. RMB
The SO asked me today, "what are you going to do to day"? I said "nothing".  She said, "that's what you did yesterday"! Me, "Yes love, but I was not finished yet"!!!!!!!!
Smirk

Reply

#29
...and make sure you put some teflon tape on the threads.
Uhoh
Reply
Water pipe union


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.