#31
Hello friends
Dust dust everywhere. I have a dust collector hooked up to several machines and takes up of 90 % of the dust. The problem sometimes I see some dust on the wall or on some storage boxes, even on the floor. Most the dust and chips from the wood was extracted into the dust collector. The question what to do what with small fine dust in the shop. Maybe I should make one filter but I do not if this is going to solve the problem.
Looking forward for your reply in this matter.

Reply

#32
A filter will help (a lot) but you might find it's almost impossible to eliminate all of it. But the filter (or maybe 2) will catch a lot of it.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#33
The small fine dust is the most dangerous for your lungs. Buy a hanging air filtration unit.
Wen, Grizzly, Jet, Powermatic, and several other companies sell them in different CFM ratings.

http://www.grizzly.com/products/Hanging-...peed/G0738
http://www.grizzly.com/products/Hanging-...mote/G0572
http://www.rockler.com/dust-collection/air-filtration
Reply
#34
Open all the windows and doors on a windy day.  Fire up an electric powered yard blower.  Have fun.
They told me anybody could do it, but I showed them.
Reply
#35
(05-19-2017, 07:28 AM)Lucky Irish Wrote: The small fine dust is the most dangerous for your lungs. Buy a hanging air filtration unit.
Wen, Grizzly, Jet, Powermatic, and several other companies sell them in different CFM ratings.

http://www.grizzly.com/products/Hanging-...peed/G0738
http://www.grizzly.com/products/Hanging-...mote/G0572
http://www.rockler.com/dust-collection/air-filtration

I have the 2nd one on the list and turn it on when I walk into the shop - the outlet its on is part of my lighting circuit.

You say you have dust collection - what filter media are you using? If its just a bag you should think about upgrading to a canister filter. Between the overhead and the canister on my HF DC my basement shop is virtually dust free - as in nothing on flat surfaces even after using the TS. As Lucky says - its the fines that will hurt you so upgrade and wear a mask.
Reply
#36
(05-19-2017, 07:30 AM)David G Wrote: Open all the windows and doors on a windy day.  Fire up an electric powered yard blower.  Have fun.

This happens in my shop every other week. Use a mask and goggles when doing it. Blow it out, let it settle for about five minutes, then do it again. Get some fans going in the direction you are blowing to help encourage the flow.
Just because shooting fish in a barrel is easy, that doesn't mean there are some fish that should remain unshot.
www.WestHillsWood.com
www.HOPublishing.com
FACEBOOK: #WoodShopWednesday
Reply
#37
I had one of the Delta air filters, just like the ones listed above.
The motor bearings went on it and it was as much as a new unit to replace the motor so I tossed it.
It was also noisy as heck.
I built a downdraft sanding table with a furnace blower and a couple layers of good furnace filters...almost silent and it works great.
I was just about to build another to hang like the Griz/delta/whatever but instead I am making one on wheels so that I can move it to the door and take the filters out and when I blow down the shop I don't need a windy day, just a window open at the far end and the blower at the door.
The furnace blower and motor is the way to go. Quiet enough you almost forget its on and the filters are cheap
For The Love Of Wood
Reply
#38
Us a bungee cord to attache a 20" square furnace filter to a box fan.  Run the fan and it will pick up airborne dust.  Hang it from the ceiling or leave it on the floor.  

Replace the filter as needed.  

Double stack a fiberglass filter and a 3M fine filter.  The fiberglass filters are just a couple of dollars and will trap the larger particles and make the 3M filter last a lot longer.  The 3M filters can cost between $10.00 and $20.00 each depending upon the micron rating on the filter.

You could attach some sort of holder for the filter, but the bungee works just fine (looks like crap though).

Box fans cost between $10.00 and $20.00 each, but you probably have one in the house already.
No animals were injured or killed in the production of this post.
Reply
#39
Even with good Dust Collector and  air filtration unit/s I do not thing anyone will get 100% out and that is why a face mask is needed
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#40
(05-19-2017, 11:35 AM)Arlin Eastman Wrote: Even with good Dust Collector and  air filtration unit/s I do not thing anyone will get 100% out and that is why a face mask is needed

I added dust collection after the service man from the oil company said that they would not renew my service contract if I didn't do something about the dust.  

I don't know how the dust affects an oil burner but apparently there will be less maintenance required if you control the dust.
No animals were injured or killed in the production of this post.
Reply
how to get rid of fine dust in the shop


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.