#38
Looking for ideas or plans for drill press table. Ive had too many close calls holding things, even when I know better I do stupid. Any photos, links or suggestions are welcome!.
Watch your fingers!!


Reply

#39
The Black & Decker Workmate is very sturdy and the drill press can be clamped in place.  It is versatile and can be folded out of the way.

[Image: 916qHxi1LkL._SL1500_.jpg]

I doubt that you can produce a base for much less than $67.00.

https://www.amazon.com/Decker-WM225-Port...dpSrc=srch
No animals were injured or killed in the production of this post.
Reply
#40
Don't have any plans, but you could look around and come up with some. Grizzly, Woodcraft, & Rockler probably have the basic table. Woodpeckers has a very nice table. Pat Warner probably has/had one of the best.

Don't make your fence too tall (it will hit your feed handles).
Explore the different types of clamping: cam, toggle, threaded knob, etc.
I'd put four T-Tracks in the table. One on each side of the spindle close, and one toward the outside edges.
Make your sacrificial block square, not round.
Reply

#41
(11-14-2017, 01:15 PM)DieselDennis Wrote: Don't have any plans, but you could look around and come up with some.  Grizzly, Woodcraft, & Rockler probably have the basic table.  Woodpeckers has a very nice table.  Pat Warner probably has/had one of the best.  

Don't make your fence too tall (it will hit your feed handles).  
Explore the different types of clamping:  cam, toggle, threaded knob, etc.
I'd put four T-Tracks in the table.  One on each side of the spindle close, and one toward the outside edges.
Make your sacrificial block square, not round.

Looked at a ton of google photos and you hot the nail on the head as I see them
Watch your fingers!!


Reply
#42
(11-14-2017, 01:15 PM)DieselDennis Wrote: Make your sacrificial block square, not round.

Why? With a round sacrificial block, you get multiple fresh backing opportunities. With a square one, you get four.
Reply
#43
This is the table I built for my 11-inch Delta No. 645 benchtop drill press. I wanted something small, simple and light weight. My table has 1/2-inch oak edge banding and a tempered hardboard work surface.

http://www.runnerduck.com/drill_press_table.htm

Here's another simple table with good instructions and lots of answered questions.

https://www.wwgoa.com/article/shop-made-...ble-plans/
Reply

#44
(11-15-2017, 03:16 AM)Lynden Wrote: This is the table I built for my 11-inch Delta No. 645 benchtop drill press. I wanted something small, simple and light weight. My table has 1/2-inch oak edge banding and a tempered hardboard work surface.

http://www.runnerduck.com/drill_press_table.htm

Here's another simple table with good instructions and lots of answered questions.

https://www.wwgoa.com/article/shop-made-...ble-plans/

Doesn't Harbor Freight make a decent one?  If I remember right, it's adequate, and cheap.  Costing about the same as it would to buy just the hardware/T tracks.  I think it reviews well.
Reply
#45
I built this one from Woodsmith. I still haven't decided if I like the crank arrangement...it works well enough, but the press is limited to use with that table mounted. I used to switch mine back and forth the the stock table for occasional metal drilling.


[attachment=5715]
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#46
I just recently went through this effort myself ... no pictures yet, but ...

Quote:Don't make your fence too tall (it will hit your feed handles).  
Explore the different types of clamping:  cam, toggle, threaded knob, etc.
I'd put four T-Tracks in the table.  One on each side of the spindle close, and one toward the outside edges.
Make your sacrificial block square, not round.

Add ... make a relief notch at center of fence for the quill.

Knowing how you expect to clamp will drive other design considerations. i.e. a track on the fence for stops, where and how many tracks in the table top for clamping.

I found [color=#000000]https://www.amazon.com/Aluminum-Track-Accepts-Countersunk-112122/dp/B073NSCDTQ/ref=sr_1_1?ie=UTF8&qid=1510764145&sr=8-1&keywords=Lot+2+Each%2C+36%22+Aluminum+T+Track+3%2F4%22+by+3%2F8%22+Slot%2C+Accepts+1%2F4%22+Hex+Bolts%2C+1%2F4%22+or+5%2F16%22+T+Bolts%2C+Countersunk+Holes+Every+6%22+112122]these T-Tracks on Amazon to be the cheapest available.

Also I really like these auto-adjust toggle clamps:
http://www.rockler.com/armor-stc-hh70-au...gh-profile

Only other thing to consider is dust collection ... will you use sanding drums for example?
I intend to use sanding drums ... so I built my table on a box with DC underneath.
Additionally this allows me full use of the existing crank and table lock.

Quote:With a round sacrificial block, you get multiple fresh backing opportunities. With a square one, you get four.

Well, eight
Wink 

For me, I can make straight edges quicker and more easily than round and I don't use a fresh backer for every drilling opportunity.

 
~Dan.
Reply
#47
Not perfect but gets the job done quick.  Mine is this one: https://www.harborfreight.com/drill-pres...96395.html It's about $20 right now on the site.  I will build a better one in the future. Dan
Reply
Table for Drill Press


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.