#26
I'm designing a small cabinet for my SIL's home office that will hold a printer on top, the cpu on a shelf and printing paper on the bottom. Dimension will be 22" wide, 24" deep and 28" high.

The table will be in the space below.

The cabinet will be cherry which brings me to my question. Since cherry darkens with light and there will be a printer on top, I thought it would be good to have something else on the top besides cherry so it doesn't get a shadow. A leather or cork pad, for example, or some type of veneer or inlay.

What would you suggest?

Cliff
‘The problem with the world is that intelligent people are full of doubts, while the stupid ones are full of confidence
Charles Bukowski
Reply

#27
Cliff,  I like the idea of a leather pad, since that will cut down on scratches.  If that doesn't work, you might want to look at maple.  I don't think light will have much of an impact on it, though it can impact some finishes.  Walnut is my favorite wood to work with, but it gets bleached out with sunlight, so I would stay away from that or cherry.
Reply
#28
Leather, glued and held down with brass escutcheon pins.

http://www.heathsrestoration.com/designs.html

[Image: multi_line_design_leather_sample_4-161x145.jpg]
No animals were injured or killed in the production of this post.
Reply
#29
A glued leather top sounds perfect. Thank you both for the suggestions.

Cliff
‘The problem with the world is that intelligent people are full of doubts, while the stupid ones are full of confidence
Charles Bukowski
Reply
#30
Bonded leather, which is the leather equivalent to MDF, might be an economical alternative.  While I would not want to use bonded leather for a jacket or for a chair, the product has been used for many, many years for wedding album covers and book binding where the amount of stretching is minimal.

I now see that the bonded leather technology is making this product useful to the furniture industry, but personally I would not use it for upholstery.

But for your non-flexing, non-stretching table top environment it should do just fine.  The color and finish are top coat only, and are the same as the top coat only leather used in jackets and furniture.

The best leathers are "vat dyed" and the color runs all the way through.  While that is nice for a jacket, it is not an issue for table tops.
No animals were injured or killed in the production of this post.
Reply
#31
I've used 1/4-inch glass for desks and table tops.

http://www.luxuryroomdecor.com/mediaimag...906443.jpg
Reply

#32
(12-16-2017, 01:23 PM)Lynden Wrote: I've used 1/4-inch glass for desks and table tops.

http://www.luxuryroomdecor.com/mediaimag...906443.jpg

I think he is most worried about the effects of UV on the wood, and its changing color.  Glass is a great option for protection from scarring, but not from sunlight or UV.
No animals were injured or killed in the production of this post.
Reply
#33
Cliff,

If you're going to glue down a leather top, I suggest you use something other than solid wood for the substrate. A wide solid wood top will probably give you problems with a glued down leather surface because of the expansion and contraction of the wood. I suggest Baltic birch plywood of perhaps MDF, and border it with cherry after you've glued down the leather. I was planning on doing a leather inlay writing surface on a walnut desk I'm building. My research steered me away, at least for the moment, because of the wood movement issue. I may build a second writing surface with BB ply bordered with walnut as I suggested and glue the leather to the BB ply - depends on whether I have enough energy left when I get done with the desk.

Hank
Reply

#34
(12-18-2017, 02:15 PM)Hank Knight Wrote: Cliff,

If you're going to glue down a leather top, I suggest you use something other than solid wood for the substrate. A wide solid wood top will probably give you problems with a glued down leather surface because of the expansion and contraction of the wood. I suggest Baltic birch plywood of perhaps MDF, and border it with cherry after you've glued down the leather. I was planning on doing a leather inlay writing surface on a walnut desk I'm building. My research steered me away, at least for the moment, because of the wood movement issue. I may build a second writing surface with BB ply bordered with walnut as I suggested and glue the leather to the BB ply - depends on whether I have enough energy left when I get done with the desk.

Hank

Why?  Leather has lots of give.  It will stretch and contract.
No animals were injured or killed in the production of this post.
Reply
#35
Hank,

That's exactly what I was thinking of doing. Added advantage is that there would be no movement concerns with the top.

Cliff
‘The problem with the world is that intelligent people are full of doubts, while the stupid ones are full of confidence
Charles Bukowski
Reply
Suggestions needed for a cabinet top


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.