▼
Posts: 4,787
Threads: 0
Joined: Apr 2005
Location: Macomb, OK
The rubber pad came off my festool sander. It's in Uruguay, but I'm in the US at the moment so I can't look at it myself. My son sent me the picture. I'm not sure if this is broken or if this reattaches somehow. Does this pop back on? Maybe needs new adhesive to hold the pad on? Maybe a bolt vibrated loose? What does everyone think?
Since I'm here, if I need to order another part, I should do it now and take it back with me.
brian
Shut up and take your medicine, citizen.
▼
Posts: 1,150
Threads: 0
Joined: Nov 2006
Location: Texas - Gods Country
(02-28-2018, 11:32 AM)blanning Wrote: The rubber pad came off my festool sander. It's in Uruguay, but I'm in the US at the moment so I can't look at it myself. My son sent me the picture. I'm not sure if this is broken or if this reattaches somehow. Does this pop back on? Maybe needs new adhesive to hold the pad on? Maybe a bolt vibrated loose? What does everyone think?
Since I'm here, if I need to order another part, I should do it now and take it back with me.
brian
It is NOT broken. It needs a new backing pad. Those are a wear item. After long periods of storage, or lots of use, they need to be replaced. They are very easy to swap in and out. Look up the model and order from festool. Around $45 and you'll be good as new.
The one on it now CANNOT be repaired. Must be replaced.
▼
Posts: 4,787
Threads: 0
Joined: Apr 2005
Location: Macomb, OK
(02-28-2018, 11:42 AM)Strokes77 Wrote: It is NOT broken. It needs a new backing pad. Those are a wear item. After long periods of storage, or lots of use, they need to be replaced. They are very easy to swap in and out. Look up the model and order from festool. Around $45 and you'll be good as new.
The one on it now CANNOT be repaired. Must be replaced.
I see the bolt there in the center and the attached allen wrench. I'll order a new one. Thanks.
Shut up and take your medicine, citizen.
▼
Posts: 1,150
Threads: 0
Joined: Nov 2006
Location: Texas - Gods Country
02-28-2018, 12:11 PM
(This post was last modified: 02-28-2018, 12:12 PM by Strokes77.)
(02-28-2018, 11:48 AM)blanning Wrote: I see the bolt there in the center and the attached allen wrench. I'll order a new one. Thanks.
Just get the correct one. One version uses the bolt, like yours, and one is tool less and snaps in. The allen key that is attached is the tool to change yours.
Posts: 23,922
Threads: 2
Joined: Sep 2003
Location: Missouri
Yes looks like age got it. That happened to mine. It wasn't the whole pad, just part of it came loose.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
▼
Posts: 4,787
Threads: 0
Joined: Apr 2005
Location: Macomb, OK
(02-28-2018, 12:39 PM)Stwood_ Wrote: Yes looks like age got it. That happened to mine. It wasn't the whole pad, just part of it came loose.
Age gets me all the time.
Shut up and take your medicine, citizen.
▼
Posts: 9,459
Threads: 0
Joined: Dec 2004
(02-28-2018, 01:38 PM)blanning Wrote: Age gets me all the time.
If only we could just order and replace you with a new one
Glad its my shop I am responsible for - I only have to make me happy.
Posts: 3,535
Threads: 0
Joined: May 2005
Location: Greater Fort Collins Area, CO
LOL Mike!
Yes, pads fail, had the displeasure of learning that apparently both of of my festools failed in the 3 years they were in storage (while I was between shops) and when I went to use on a project, ETS 150 popped off, no worries.. grab my Rotex... zzz, fling. Grrr.
Looking into it, essentially Festool uses very good quality foam, like high end speaker surrounds, and like speakers - foam rot occurs. (had to rebuild a few sets over the years)
Found replacements on Amazon for a reasonable fee. ~ $40
Michael
Every day find time to appreciate life. It is far too short and 'things' happen. RIP Willem
▼
Posts: 4,787
Threads: 0
Joined: Apr 2005
Location: Macomb, OK
(02-28-2018, 03:28 PM)MichaelS Wrote: LOL Mike!
Yes, pads fail, had the displeasure of learning that apparently both of of my festools failed in the 3 years they were in storage (while I was between shops) and when I went to use on a project, ETS 150 popped off, no worries.. grab my Rotex... zzz, fling. Grrr.
Looking into it, essentially Festool uses very good quality foam, like high end speaker surrounds, and like speakers - foam rot occurs. (had to rebuild a few sets over the years)
Found replacements on Amazon for a reasonable fee. ~ $40
Michael
I found them. I also picked up a strip of the clear track saw edge.
I'm wondering what other cool new tools or accessories I should be buying while I'm here.
Shut up and take your medicine, citizen.
▼
Posts: 23,922
Threads: 2
Joined: Sep 2003
Location: Missouri
(02-28-2018, 03:45 PM)blanning Wrote: I'm wondering what other cool new tools or accessories I should be buying while I'm here.
Oh..........one of everything.......
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
|
