#22
Had a bunch of these Ash scraps I was going to use up....before the Gall Bladder Episode...finally getting around to making a small box out of the stuff...trying to get the most out of the least, as it were
Rolleyes 

Start up meant I needed a few glue ups prepped...
[attachment=17323]
I found 4 pieces close to the same size...and jointed the edges...all at once.   Flipped things around, to find two that were close to a match, and glued those two together..
Cool 
[attachment=17324]
Middle needed cauls to keep it flat....Still had two more to do..
[attachment=17325]
At least these two went together better...
Rolleyes 
[attachment=17326]
Still have a stack of thins for ends?
Rolleyes 
[attachment=17327]
And a few thicker parts, as needed 
[attachment=17328]
And..even have a few to glue up into a lid panel...
Cool
[attachment=17329]
3/8" thick, mostly
Rolleyes    May find a few uses for these?
Confused  
[attachment=17330]
One seems to be out and about?  I think I might have a spare
Rolleyes 

That's the start, will see how things turn out...
Stay tuned..
Winkgrin
Show me a picture, I'll build a project from that
Reply

#23
Keep it up, Steve!
Waiting to grow up beyond being just a member
www.metaltech-pm.com
Reply
#24
One panel is out of the clamps,  issues with the hands shaking way too much
No .   panel has been planed flat....will need the ends squared up.  maybe tomorrow, I can get something done...
Rolleyes
Show me a picture, I'll build a project from that
Reply
#25
Panel is cleaned up...
Winkgrin  
[attachment=17345]
Plane of choice for this Ash?
Confused  
[attachment=17346]
Stanley No. 3c.    has 3 patent dates....seems to be a "tweener" between Type 11 and Type 12....has a SW iron on board.   seems to work decently enough
Cool 
[attachment=17347]
I'll get to this one, tomorrow.....I also managed to get an "end" panel in the clamps....couple of passes along the mating edges with the plane..
[attachment=17348]
To remove any gaps.    Vise does a good job of acting as a helping hand.   Found two more scraps for the other "end"
Rolleyes 
[attachment=17349]
This might take more than just a couple passes to joint the edges..
Confused 

May do a "Box Joint" for the corners....hand cut, of course.   We'll see, no rush right now...
Rolleyes 

Stay tuned..
Winkgrin
Show me a picture, I'll build a project from that
Reply
#26
Reason I use that #3c size plane for these thin parts...
Confused 
[attachment=17371]
The #4c feels a bit too big
Rolleyes 
[attachment=17372]
Got a couple panels out of the clamps today..and a fourth one into the clamps
Cool 
[attachment=17373]
#4 needed a lot of work done...just to get two edges to meet gap-free
Rolleyes
[attachment=17374]
#3 got cleaned up....was a bit wider than the long panels....needed an edge jointed..
Cool  
[attachment=17375]
Cleaned up Panel #2..
[attachment=17376]
And set it with #1 and #3....waiting on #4 to cure.....got to thinking
Uhoh  maybe instead of one LARGE box....maybe a match pair of smaller boxes?
[attachment=17377]
Have enough for two lids, anyway....marked a center line
Cool
[attachment=17378]
Tablesaw to square the ends, and split the center line....then repeat for the two longer panels...first one got set with the ends..
[attachment=17379]
Then the long panel below this mess was also cut....still waiting on glue to dry
Rolleyes
[attachment=17380]
Lid parts might be a tad too long, but that is better than too short.   Can cut both down to sizes needed...

Have a 6mm mortise chisel ( Narex) that will get used to lay out the "fingers" for the Box Joints....Backsaw and chisel to remove the waste.   maybe by Tuesday, I can start on that?
Confused 
Stay tuned
Winkgrin
Show me a picture, I'll build a project from that
Reply
#27
Monday being Monday
Rolleyes  Shop is closed today.   I may go to check on the glued up panel after supper...we'll see.
Winkgrin

Thinking a 1/4" plywood bottom panel, glued and nailed in place....MAYBE some shop-made molding around the bottom to hide the plywood edges...
Confused


Whether to hinge the lids, or add a piece under the lid, and have it just lift off the box...?
Confused 

Finger joint layouts and start ups, tomorrow....I hope.
Rolleyes

Stay tuned..
Winkgrin
Show me a picture, I'll build a project from that
Reply
#28
Will update in the morning, but....maybe a tease?
Confused  
[attachment=17437]
Dry fit of two of the corners...will be working on the other end, tomorrow....
[attachment=17438]
Done at the bench, with just hand tools, BTW..
Cool 

Stay tuned..
Winkgrin
Show me a picture, I'll build a project from that
Reply
#29
Oh, fun.  Looking forward to more details.
Reply
#30
well, first I got 3 boards to match up enough to do a glue up..
Rolleyes
[attachment=17442]
From this mess into..
[attachment=17443]
This.  Stashed it over in a corner, out of the way...
Box #1 long sides needed squared up to match each other, then clamped in the vise..
[attachment=17444]
Combo Square to mark a "baseline" all around, showing how thick the ends are, then..
[attachment=17445]
I used a 6mm chisel to lay out the spacings for the fingers...
[attachment=17446]
Then a small square to mark across and down the faces,  needed to guide a saw
[attachment=17447]
Goal being to split these lines, or, at least cut on the waste side...
[attachment=17448]
After which, the two go their separate ways, easier to chop one board at a time...
[attachment=17449]
Chopped halfway, leave a tab for support, for when I flip the board over...
Cool
[attachment=17450]
Then use these, to lay out the cuts, and chops for the matching end piece....goal here was to leave the lines, and cut the waste...that was the goal
Rolleyes
[attachment=17451]
First set is on the left, second set was a little bit better....later today (maybe
Rolleyes ) I can work on the other end....now that I have a bit of practizing done
Winkgrin 

Stay tuned..
Winkgrin ..BTW, when I chop those little squares of waste out...they tend to fly straight back at me...
No
Show me a picture, I'll build a project from that
Reply
#31
Got the rest of the corners for this box done, today...
Cool 
[attachment=17483]
Nice when I need a mallet to drive these together
Winkgrin 
[attachment=17484]
And check for square...
Confused 
[attachment=17485]
One down, one to go? 
[attachment=17486]
May just go ahead, and complete Box #1....lid is out of the clamps..
[attachment=17487]
A little bit big, but, I can cut away the "bad" parts, and make sure the rest is square and flat...
[attachment=17488]
Managed to pick up some hinges, today...not so sure about the "new" Mitre Saw, though
Rolleyes 
[attachment=17490]
May wait until it grows up
Confused
Winkgrin 
Back started hurting, time to quit for the day....Stay tuned
Winkgrin
Show me a picture, I'll build a project from that
Reply
Ash Box Project..


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.