▼
Posts: 3,723
Threads: 0
Joined: Nov 2010
Instead of a lid...it will have a pair of doors....
Sorted through the stack of parts...looking for enough to make the doors with..
[attachment=46804]
Figured I'd start with the doors, and size the rest to them...
[attachment=46805]
Jointed matching edges...then cross cut for length from those straightened edges..then glue up a panel
[attachment=46806]
Then do the second door, same as the first...
[attachment=46807]
and set these aside, for now...
[attachment=46808]
And, see about 2 sides and 2 ends....sides were the easy part...just rip a board right down the center..
[attachment=46809]
Maybe clean up the saw marks along the edges...
[attachment=46810]
But...needed to flatten things out a bit..
[attachment=46811]
Hmmm....we have ways..
[attachment=46812]
That was the 2 sides...the 2 blanks for the ends?
[attachment=46813]
Would be a different story...
Stay tuned....
Show me a picture, I'll build a project from that
▼
Posts: 3,723
Threads: 0
Joined: Nov 2010
The 2 blanks for the ends...shorter one was too bad, a bit of clean up with the plane was about it...the longer one? The more I worked on it, trying to get it flat, the thinner it became, until I simply scrapped it...Did not have another blank long enough to replace it, that matched the thickness I needed...so..
[attachment=46814]
This is called a kerf cut. tablesaw can not reach high enough to meet in the middle...Set the fence to leave just over the thickness I needed..then the hand saw took it from here..
[attachment=46815]
Old D8 ( no hyphen) rip saw..a little Cardio for the day...results?
[attachment=46816]
This is the blank I was trying to match up to...
[attachment=46817]
Then cut away what didn't match for size...length and width...and cutting for best look...
[attachment=46818]
Waiting to see what size I need to make the box....doors are about ready to clean up..
[attachment=46819]
Get these 2 squared up, and flat...then milled for bread board ends...and then..
[attachment=46820]
Where the 2 doors meet, they will lap.
Wednesday was Pay Day...bills to pay shopping to do..and a stop at Hobby Lobby to replenish the stash of hardware...
[attachment=46821]
So..will see how things go, today...
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
4 squared this morning..
[attachment=46822]
Match up for grain details..
[attachment=46823]
getting the bread board end blanks ready
[attachment=46824]
Milled tongues on the ends of the door panels...then used this set up to mill the grooves..
[attachment=46826]
And that is door #1 in the clamps, waiting on glue to dry. Door #2?
[attachment=46827]
Is sitting over on the bench, for now...Details?
[attachment=46828]
Sometime around 1800 or 1900 hours, I'll head back to the shop...and clean them up...maybe tomorrow, I can start on the 4 sides of this project..
Stay tuned..
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
Doors have been cleaned up, bread board ends have been trimmed. Everything is flat...made a few cuts on the tablesaw..
[attachment=46849]
Had to double check which cut went where...
[attachment=46850]
I think a latch will go about in the center...
Now that the doors are to final size...I can cut the 4 box sides to size..
[attachment=46851]
And see how big a box we are looking at...
[attachment=46852]
Then lay the doors on top...
[attachment=46853]
Rather plain looking...just don't stare too long at the grain patterns...you might see something, that isn't there..
Set the doors aside, for now..lay out some Lay out tools..
[attachment=46854]
Chisel as a "layout tool"? yep, it sets the spaces for the fingers..
[attachment=46855]
Then I need a saw of some sort..
[attachment=46856]
Mr Jackson seems to fit the job...
[attachment=46857]
So..next up...some chopping to do..
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
I set up a chopping block on the bench...
[attachment=46858]
Sitting right over the top of the bench's leg...screwed down. Then a clamp to hold the part still...
[attachment=46859]
Chop from both faces, until...
[attachment=46860]
Clean this up, then..
[attachment=46861]
Trace around each finger with a sharp pencil...saw and chop the waste out..and try a dry fit..
[attachment=46862]
Pare to get a better fit. Then repeat for corner #2...
[attachment=46863]
So...later today, I'll see about the other 2 corners. I also need to see about a few dados, to hold a couple shelves/dividers....
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
All 4 corners are now done...and dry fitted together..
[attachment=46876]
Stepping off into 3rds..because..
[attachment=46877]
These need to be set into dados...
[attachment=46878]
Laid out...yep, right went I let go to push the shutter button on the camera..one board slid a bit...next,
[attachment=46879]
Knife a few lines...Then chop those lines with a 1" wide chisel to deepen the lines...and a 1/4" wide chisel to remove the waste..
[attachment=46880]
And a router plane to level the floor of the dado...dry fit?
[attachment=46881]
1 done, 3 to go...
That done, tried a dry fit of all the parts....shelves were about a 1/16" or so too long..or..the dados weren't deep enough..was easier to buzz the end of the shelves a little bit, and try again..
[attachment=46882]
No glue, yet....the hardest part will be to get this pulled into square, once the glue-up starts in, later today.....we have ways..
[attachment=46883]
Right now, this dry fit is squared up.....I need to tear this all done, make some cauls, get a brush for the glue....and a few more clamps.....
I am sure there will be cussing involved....all them clamps, and cauls..and just 2 hands available? Hmmm...and only 1 cold beer in the fridge?
Stay tuned..there may be a "Blue Streak" coming from the shop...wish me luck..
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
So, right after Lunch, today...got an assembly table ready.
[attachment=46896]
All the clamps were removed...
[attachment=46897]
Needs to be taken to the assembly table..knocked apart and set out in order...clamps were laid out, either close to hand..
[attachment=46898]
Or, hung up close by...like about 2 steps away..
[attachment=46899]
And all set up to go...Had a mallet to assist the stubborn parts along
[attachment=46900]
Bottle of glue at the ready, along with a H-F Acid Brush to moosh the blobs of glue into place
Once things start..there is no stopping to take a picture..
[attachment=46901]
Should be enough...check for square?
[attachment=46902]
If not, pull until it is...
[attachment=46903]
Over on the bench, there is a blank for the back of this thing...
[attachment=46904]
Will need to trim it for size, once the box comes back out of the clamps..in the mean time..
[attachment=46905]
Need to put most of the toys away...ya think?
Stay tuned..
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
Box is out of the clamps...
[attachment=46915]
Checked to see how the doors look..
[attachment=46916]
Will install hinges after a bit...first..need to trim the panel for the back to size..
[attachment=46917]
Cutting gauge to mark a line deep enough for the saw to follow..
[attachment=46918]
Then repeat on the end ...
[attachment=46919]
Spread some glue around, and clamp the panel to the back of the box...
[attachment=46920]
Will let this sit a day..
[attachment=46921]
Tomorrow, I'll clean it up, see about those hinges..and start on a stand...
Stay tuned...
Show me a picture, I'll build a project from that
Posts: 3,723
Threads: 0
Joined: Nov 2010
Those clamps have been removed..and the back of the box has been cleaned up...Front edges of the box have been leveled...
[attachment=46938]
Things were checked for square
Couple corners needed leveled up..
[attachment=46939]
We have ways...had thought about adding the doors, even laid out the hinges..
[attachment=46940]
Had also laid out a few pieces of scrap...
[attachment=46941]
Decided to build something this box/cabinet could stand on....made up a pattern, and cut one piece, to see how it looked..
[attachment=46942]
The hard part, to cut the matching one, so that they did indeed ...match..
[attachment=46943]
Needed a way to attach these 2 to the bottom of the case....searched through the stack of leftovers, found a decent piece of Pine...beveled the ends..
[attachment=46944]
Then did a glue-up of the 3 parts...
[attachment=46945]
(back right leg is sitting on the arm of a square, BTW)
So, later today, these clamps can come off, get everything cleaned and leveled....drill a couple countersink holes...and attach the "Stand" to the bottom of the Cabinet..
May add a bit of glue, while I am at it.....still need to install the hinges to the case and the doors,,a couple knob to the doors, and a latch...
Maybe a couple of stain? We'll see..stay tuned...
Show me a picture, I'll build a project from that
Posts: 283
Threads: 0
Joined: Nov 2019
Breadbox ends on the doors, AND a stand?! You weren't kidding about the "different"! Looks really nice.
|
