Posts: 116,083
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(02-12-2019, 04:00 PM)enjuneer Wrote: If you like that one, Paul pontificates on scrapers and sharpening for over an hour and a half in this YouTube video for the Gwinnett Woodworkers group.
,,,,,,,,,,,,
Yep...and that's a good one also, Bob...
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Posts: 2,382
Threads: 0
Joined: Dec 2011
(02-12-2019, 02:48 PM)Timberwolf Wrote: ...................
More on scrapers from Paul Hamler, who shares a few things about them.....starting about the ten mark...
Thanks, Jack, for sharing that clip.
Simon
Posts: 12,299
Threads: 0
Joined: Mar 2006
I dug th SteMac out last evening, never really used it much, as there is little
I cannot do without a card scraper. I did put a hollow grind on one edge and after a bit of experimentation, it worked very, very well!
Does anyone here know of what material that scraper is made of?
Posts: 2,701
Threads: 0
Joined: Jul 2006
I have a few really nice toothed scrapers. Most people use a different name for them. They call them rotary tool cut off wheels.
toolmakingart.com
When you have eliminated all unnecessary wood, then whatever remains, however well formed, is too small to serve as originally intended.
Posts: 10,717
Threads: 1
Joined: Jan 2006
Location: Orlando, Florida
(02-13-2019, 07:04 AM)Tony Z Wrote: Does anyone here know of what material that scraper is made of?
In the StewMac video, Al Carruth, the inventor, says it's "tool steel, very slightly tempered to about Rockwell C 62." In a blog, Alan described his first scraper made this way was O1.
http://www.alcarruthluthier.com/toolOfTh...craper.htm
Still Learning,
Allan Hill
Posts: 12,299
Threads: 0
Joined: Mar 2006
(02-13-2019, 08:26 AM)AHill Wrote: In the StewMac video, Al Carruth, the inventor, says it's "tool steel, very slightly tempered to about Rockwell C 62." In a blog, Alan described his first scraper made this way was O1.
http://www.alcarruthluthier.com/toolOfTh...craper.htm
Thanks Alan. Think I may make one about the size and shape of a card scraper, 1/4" thick, and dished out like my StewMac. Please bear in mind, when I say I may make, I really mean, one of my machinists will be doing a "government job". I was thinking O1, and I will use an outside heat treat source for heat treating and drawing to Rc62.
Posts: 257
Threads: 0
Joined: Dec 2004
Posts: 7,008
Threads: 0
Joined: Aug 2004
Location: Perth, Australia
02-17-2019, 11:36 AM
(This post was last modified: 02-17-2019, 11:37 AM by Derek Cohen.)
David, it is a 180 grit CBN wheel. That one came from Jim Carroll at the CWS Store (in Oz).
You would not (ever .. never!) want to use a diamond wheel at speed (i.e. heat) with a high carbon blade. Diamond is only good for carbide. With high carbon steels, the diamond wheel will disintegrate within a relatively short period (the graphite in diamond is absorbed by the iron in the steel). Stick to CBN - I think I got the ball rolling on these a few years ago: http://www.inthewoodshop.com/WoodworkTec...SetUp.html
Regards from Perth
Derek
|
![[Image: 1_zpspr2v0uh1.jpg]](https://i.postimg.cc/kXwr3gXp/1_zpspr2v0uh1.jpg)
![[Image: Scraper2-zpsyar2o7ii.jpg]](https://i.postimg.cc/GmSZtgDP/Scraper2-zpsyar2o7ii.jpg)
![[Image: Sharpening-blade-scrapera-zpslgrvfjha.jpg]](https://i.postimg.cc/rwpB82DF/Sharpening-blade-scrapera-zpslgrvfjha.jpg)
