Posts: 5,119
Threads: 12
Joined: Apr 2009
Location: SoMar
Some replies to my thread on rust removal have sparked another problem. The cast iron table on my scroll saw is hideously stained from having acid drain cleaner spilled on it.
Is there anything I can do to remove these stains?
I'd like to go back to a nice shiny table if possible.
Thanks for any guidance.
Posts: 22,717
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
Sand away the stained metal. It could go pretty deep. Or not. It would be a challenge to keep the table flat if the stains have any depth. A surface grinder could go a couple thousandths at a time and see what you get.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 30
Threads: 0
Joined: Apr 2014
I find oxalic acid - Bar Keeper's Friend - useful to remove most stains. Sprinkle it on and use a damp soft scrubby to make a paste and work at it.
Posts: 19,681
Threads: 0
Joined: Aug 2001
Cast iron is quite porous. It's likely that the material causing the stain has been absorbed into the cast iron and many be impossible to remove.
If you want a "shiny" tabletop, buy a new one.
Howie.........
Posts: 7,421
Threads: 1
Joined: Sep 2005
We used to "mill" small engine heads by gluing fine sandpaper on a piece of double strength glass and rubbing the cylinder head over the surface. The glass is as nearly flat as anything you can find. Though a 12" square piece of granite tile might do too. But if it does not affect functionality I would just clean it with steel wool and wax it and refer to it as "patina".
No animals were injured or killed in the production of this post.
Posts: 12,283
Threads: 0
Joined: Jun 2007
Location: Bucks County PA
I've done the same thing only I've used an old cast iron wing from a tablesaw.
See ya around,
Dominic
------------------------------
Don't you love it when you ask someone what time it is and to prove how smart they are, they tell you how to build a watch?
Posts: 5,119
Threads: 12
Joined: Apr 2009
Location: SoMar
I think I'll go with this suggestion.
I need to figure out a way to even it out all over the table though.
Posts: 7,421
Threads: 1
Joined: Sep 2005
Can you remove the table top? If so you can just bring it to a machine shop and have them grind a couple of thousandths off the top. Or you can get a large piece of double strength glass and stick down some wet/dry sand paper and rub the thing over the glass until it is clean. It should end up flat if you use a large sheet (supported on tabletop) of glass for the surface.
No animals were injured or killed in the production of this post.
Posts: 2,002
Threads: 0
Joined: Feb 2003
Herb G said:
... I need to figure out a way to even it out all over the table though.
Dump some more drain cleaner on it, spread it around until the entire surface looks uniform, then flush it off. Completely neutralize any acid with a thin paste of baking soda and water. Flush that off, dry it, and sand it.
Posts: 7,421
Threads: 1
Joined: Sep 2005
thewizzard said:
[blockquote]Herb G said:
... I need to figure out a way to even it out all over the table though.
Dump some more drain cleaner on it, spread it around until the entire surface looks uniform, then flush it off. Completely neutralize any acid with a thin paste of baking soda and water. Flush that off, dry it, and sand it.
[/blockquote]
If that were an acceptable solution (and I don't think it is) then bead blasting the surface would work better. But the problem with either of these solutions is that it will significantly increase the friction between the surface and the work piece. And I don't think you want that on a saw table.
No animals were injured or killed in the production of this post.