Posts: 528
Threads: 0
Joined: Dec 2004
I saw this little box posted on another site.
As you can see, it will have a sliding dovetail lid. The original poster cut the dovetails in the box using the router table. Since the box is made form a single piece of wood, that meant he was cutting with wood between the router fence and the dovetail bit. I assume he fed it from left to right, although he didn’t say.
I would like to make a box like this, but I am not crazy about making that cut on the router table. Is there a better way? I was thinking of doing it on the table saw, which might not give as smooth a cut, but doesn’t make me nearly as nervous as doing it on the router table.
Hank Gillette
Posts: 12,197
Threads: 2
Joined: Nov 1999
Location: Nebraska City
Almost any 'plowing cut' on the router table involves a 'buried' cut with wood between the fence. If there's a way around it, I've never figured it out.
Posts: 6,755
Threads: 0
Joined: Aug 2001
Location: Post Falls, ID
I would remove most of the material with the tablesaw and then make the final cuts on the RT with the fence set back from the bit.
But that's just me...
Dave
"One should respect public opinion insofar as is necessary to avoid starvation and keep out of prison, but anything that goes beyond this is voluntary submission to an unnecessary tyrany, and is likely to interfere with happiness in all kinds of ways."
Posts: 4,832
Threads: 0
Joined: Mar 2004
Plow out the majority of waste with a dado blade on the saw.
Follow that with a dovetail bit on the router table. Do the far cut first, flip/rotate, make the same cut along the opposite edge.
After that, move the fence incrementally and clean up the area in between.
Posts: 24,090
Threads: 0
Joined: Jan 2004
Handsaw, chisel. Watch out for the pointy parts.
Matt
If trees could scream, would we be so cavalier about cutting them down? We might, if they screamed all the time, for no good reason.
-Jack Handy
Posts: 29,152
Threads: 1
Joined: Aug 2002
Big Dave said:
I would remove most of the material with the tablesaw and then make the final cuts on the RT with the fence set back from the bit.
But that's just me...
Dave
It is not just you.....
that is the correct way to accomplish it safely
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 13,485
Threads: 0
Joined: Oct 1999
As said above, remove the waste with a straight bit or dado blade set.
Cut the dovetail closest to the fence by passing left to right, against the bit rotation. (The bit will be cutting on the inside edge) No different than any other cut.
I also recommend using a push block if the cut makes you nervous. MicroJig's GRR-RIP BLOCKs are about $25.00 each and have simply amazing friction. They will control the part and keep your hands well above the bit if anything goes bad.
Ralph
Posts: 3,861
Threads: 0
Joined: Nov 2000
JGrout said:
[blockquote]Big Dave said:
I would remove most of the material with the tablesaw and then make the final cuts on the RT with the fence set back from the bit.
But that's just me...
Dave
It is not just you.....
that is the correct way to accomplish it safely
[/blockquote]
Agreed.
Posts: 528
Threads: 0
Joined: Dec 2004
handi said:
As said above, remove the waste with a straight bit or dado blade set.
Cut the dovetail closest to the fence by passing left to right, against the bit rotation. (The bit will be cutting on the inside edge) No different than any other cut.
I also recommend using a push block if the cut makes you nervous. MicroJig's GRR-RIP BLOCKs are about $25.00 each and have simply amazing friction. They will control the part and keep your hands well above the bit if anything goes bad.
How about if I rotate the box and make both cuts on the side farthest from the fence? That way I could run it both times in the normal direction. Would that be any better, or would it make any difference?
Whatever way I do it, I want to make the two cuts without moving the fence to insure that the cuts are equal distance from the edge.
I will definitely be using a push block of some sort. I am very attached to my fingers and I want to keep it that way.
Hank Gillette
Posts: 2,002
Threads: 0
Joined: Feb 2003
If its the direction of the cut that has you worried, just push it through left to right rather than right to left. If you were using a hand held router, you wouldn't think twice about moving the router in opposite directions for inside versus outside cuts. No different on a table.
As everyone has kind of pointed out, the dovetail in the picture was not made with a single pass. Most of the center channel was removed then each side of the dovetail was cut independently.
