Walnut & Maple Fire Pit Table
#11
I had an old rusty fire pit that has been well used over the years. I figured instead of tossing it I would try my hand at turning it into something I needed.



In order to try and make this a reclaimed and recycle project I’m using some wood that was sourced from a firewood pile. This is some rough walnut from a local gun stock manufacture.



This board measure 7 ft long, 9" wide and 1" thick, and it's pretty rough.
But a few passes through the planer later...



...reveals some wood that I will have no trouble making good use of!



The fire pit base measures 32" in diameter so in order to give me room to play I cut all the walnut to 36" in length.



I was a little short on walnut, so I grabbed a piece of hard maple I had on hand. I’m a fan of asymmetrical design. Those affected by OCD, look away!

After I got a layout I liked, I applied some wood glue and clamps and let it dry overnight.



Next day I came back out to the shop and cleaned up the joints and leveled the panel out. What was my favorite part of leveling a panel with my #5? Being done with it....



There are loads of ways to cut circles out. Routers, jig saws or even table saws. For me, I like the band saw method. First step is to locate the center of the board



Drill a small hole where you will place an axis of some sort. Here I'm using a 13/64" shelf pin as the axis around which the piece will spin.

I use my 13/64" bit and drill about 3/4 of the way through the board from the bottom side.



The circle is cut at the band saw with my “super fancy” circle cutting jig. It’s just a board, clamped to the table with some holes drilled in it. A 34" circle means you need a 17" radius.

Just line up the pin with the hole that is the correct distance from the blade.



After it's in the right hole, just turn on the band saw and slowly spin the table top around: circle!



I had some gaps and defects in these boards and I wanted to fill those holes in order to give the surface a nice uniform look. I mixed up some 5 minute epoxy and some black pigment and patched as needed.



While I waited for the epoxy to dry I spray painted my base. The color is Ivory Silk.



I might have sprayed my toenails…



The last thing to do on the top was sand it smooth and add a finish. I used three coasts of water base wipe on poly.



I then drilled out some elongated screw holes in the base to allow for seasonal wood movement of the top and attached it with 4 screws.



It’s now a comfortable, yet rustic coffee table for my patio room. I’m more than pleased with it. I’m also happy to have reclaimed some trash and made of use again.





Thanks for looking!
Peter Brown

I can fix that...

shop-time.net
Reply
#12
A very good idea....turned out really nice.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#13
Not at all what I was expecting from the title but it looks really nice.

I'm going to recommend that method for toenail painting to my wife. Looks like it would be a lot faster than her current method.
Reply
#14
Looks good and the video turned out great!

Jake
"Above all else, he's a happy woodworker, and he'll be laid in his coffin with the most unexplainable grin on his face for he has known he has lived." -Cian
Reply
#15
Nice. Who makes a water based wipe on poly?

John
Reply
#16
Really well done. I too like the contrasting woods. And as one above said, I wasn't at all expecting that table.

Joel
USN (Corpsman) 1968-1972
USAF Retired Aug 31, 1994
Santa Rosa County, Fl Retired Jun 1, 2012
Now just a hobbiest enjoying woodworking!
Reply
#17
Peter I really like your table. I like asymmetrical too.

Trash to treasure is a good thing

It would appear the grade of firewood in your parts is of a much higher quality than what I find locally. That Walnut has some wild grain.
Worst thing they can do is cook ya and eat ya

GW
Reply
#18
Nice up-cycling there, Peter! That touch of maple really works.
Bob
"All that I do or say is all that I ever will be"

Billy Joe Shaver, Old Five and Dimers Like Me
Reply
#19
Just exactly how in the world does a walnut board "7 ft long, 9" wide and 1" thick" end up in your firewood pile???? Holy moley.


g
I've only had one...in dog beers.

"You can see the stars and still not see the light"
The Eagles: Already Gone
Reply
#20
Cool!

Doug
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.